background image

ADCP-90-250
Issue 1, November 1996

Page 2

 1996, ADC Telecommunications, Inc.

Admonishments

Important safety admonishments are used throughout this manual to warn of possible hazards to
persons or equipment. An admonishment identifies a possible hazard and then explains what may
happen if the hazard is not avoided. The admonishments — in the form of Dangers, Warnings,
and Cautions — must be followed at all times. These warnings are flagged by use of the
triangular alert icon (seen below), and are listed in descending order of severity of injury or
damage and likelihood of occurrence.

DangerDanger is used to indicate the presence of a hazard that will cause severe
personal injury, death, or substantial property damage if the hazard is not avoided.

WarningWarning is used to indicate the presence of a hazard that can cause severe
personal injury, death, or substantial property damage if the hazard is not avoided.

CautionCaution is used to indicate the presence of a hazard that will or can cause
minor personal injury or property damage if the hazard is not avoided.

1. DESCRIPTION

1.01 This section provides functional, physical, and technical descriptions of the wall box.
See 

Figure 1

.

8513-A

Figure 1. FTD1 36-Fiber Wall Box

Summary of Contents for ADCP-90-250
















Reviews: