manualshive.com logo in svg

ADB Safegate RELIANCE Omni 1-Dome, User Manual

Share
Download
ADB Safegate RELIANCE Omni 1-Dome User Manual Download Page 41

6.4.8 Replacing Lens and Flat Gasket

1. Disassemble the light assembly.

Refer to 

Disassembling the Light Fixture

 section.

2. Unscrew the eight M6 metric torx cap screws and then remove the assembled LED bracket and LED support plate.

Figure 14: Flat gasket

Note

The two M6 torx Cap Screws used to mount the optical assembly bracket to the top cover are longer than the

others.

3. Remove the Flat Gasket. Refer to 

Figure 16

.

4. Turn the top cover over and push the lens and gasket out of the pocket in the cover.

CAUTION

Cracked or broken glass is very sharp. Take necessary precautions to protect hands from being cut.
Failure to follow this instruction can result in injury or equipment damage.

5. Make sure you do the following before you continue:

Option

Description

If the lens is cracked, pitted, or damaged,

discard the lens and gasket and replace with new lens and gasket.

If just the gasket is damaged,

replace the gasket on the lens.

UM-5073, Rev. 1.0, 2021/07/13

31

Copyright 

©

 ADB SAFEGATE, All Rights Reserved

Summary of Contents for RELIANCE Omni 1-Dome



































































Reviews:

No comments

Brands by name

Popular brands

Load more brands