ADB Safegate RELIANCE Omni 1-Dome User Manual Download Page 22

Page: 22 / 66

WARNING

Do not damage the cable insulation.

CAUTION

Do not unpack the fixture before it is at the installation site to avoid damage due to transportation and handling.

4.3 Tools required

The following tools are recommended for installation.

•

One Box spanner 16/17 mm

•

One torque wrench with a 16/17 mm socket

•

Two large flat headed screwdrivers for lifting the light fixture

•

One T20 Torx key

•

One brush or cloth

•

One 3 mm Allen key

Note

Provided that the base intended to receive the light fixture has been properly installed, no other specific tool is

required.

4.4 Torquing and Installation Guidance for In-pavement Fixtures

In-pavement fixtures must be installed according to the plans and specifications; the applicable regulatory guidance; and the

following guidance. The importance of using the proper fixture clamping components and bolt torque to minimize the risk for

fixture failure or loosening of clamping components cannot be overemphasized. Refer to FAA Engineering Brief No 83 (latest

revision) for torque and installation guidelines for this fixture.
Also see our Product Center at

www.adbsafegate.com

CAUTION

Read installation instructions in their entirety before starting installation.

•

Failure to follow the installation guidance could result in bolt loosening or bolts breaking off, resulting in

catastrophic failure of the fixture and/or the mounting system components.

•

Failure to follow these warnings may result in serious injury or equipment damage.

4.5 Installation and Removal of the 8-inch Light Fixture

Installing the light fixture in a base
Installation instructions for the inset light fixtures as follows:

•

Light bases shall be installed with care to assure vertical and azimuth alignment of fixture.

•

Provide 60–90 cm / 2–3

‑

feet cable slack within light base to allow transformer servicing.

RELIANCE Omni 1-Dome,
Installation

12
Copyright

Summary of Contents for RELIANCE Omni 1-Dome


























































Search results

Summary of Contents for RELIANCE Omni 1-Dome

Reviews:

Brands by name

Popular brands

ADB Safegate RELIANCE Omni 1-Dome, User Manual

Search results

Summary of Contents for RELIANCE Omni 1-Dome

Reviews:

Brands by name

Popular brands