ADB Safegate RELIANCE Omni 1-Dome User Manual Download Page 18

Page: 18 / 66

NOTICE

RELIANCE IQ light fixtures are not fail-open light fixtures. When IQ is activated the monitoring as well as the control

functionality is handled by the ILCMS system.

3.2 Taxiway Edge

Compliance with Standards (current versions)

FAA

L-852T(L)

ICAO

Annex 14, Volume 1

IEC

61827

EASA

CS-ADR-DSN

Canada

TP 312

Australia

MOS 139

Uses

The RELIANCE

™

8-inch omnidirectional low-protrusion inset LED light fixture is provided with blue or yellow LEDs. This fixture

can be used in the following applications:

•

ICAO Taxiway Taxiway Edge, FAA L-852T(L)

•

Intermediate Holding Position (MOS)

Features and Benefits

Efficiency

•

RELIANCE IQ with integrated intelligence

•

RELIANCE with integrated fail-open technology

•

Operates on 3- or 5-step ferroresonant or thyristor CCRs designed in compliance with IEC or FAA requirements

•

Easy maintenance due to modular design, few mechanical parts

Sustainability

•

Light-emitting diode (LED) technology that offers a long-lasting light source with low power consumption

•

IP68 protected (all fastenings in stainless steel)

•

Compatible with existing infrastructure

•

Fixture compatible with all ADB SAFEGATE 8-inch bases

Safety

•

Failed LED detection according to FAA Engineering Brief No.67D

Power Supply

An integrated, encapsulated 6.6A electronic converter. Two-pole L-823 FAA Style 6 (2-pin-) plug for connection to the

transformer. Power factor typically >0.95 at 6.6 A.
French (flat 3-pin) plugs are also available for the French market. Please check ordering code.

Maintenance and Installation

Refer to the RELIANCE user manual of the RELIANCE 8-inch 1-dome omni light and to the interoperability info for installation

in a specific base.

RELIANCE Omni 1-Dome,
General Information

8
Copyright

Summary of Contents for RELIANCE Omni 1-Dome


























































Search results

Summary of Contents for RELIANCE Omni 1-Dome

Reviews:

Brands by name

Popular brands

ADB Safegate RELIANCE Omni 1-Dome, User Manual

Search results

Summary of Contents for RELIANCE Omni 1-Dome

Reviews:

Brands by name

Popular brands