ADB Safegate RELIANCE AC User Manual Download Page 22 | Manualshive

Page: 22 / 56

background image

4.2 Tools required

The following tools are recommended for installation.

•

One Box spanner 16/17 mm

•

One torque wrench with a 16/17 mm socket

•

Two large flat headed screwdrivers for lifting the light fixture

•

One T20 Torx key

•

One brush or cloth

Note

Provided that the base intended to receive the light fixture has been properly installed, no other specific tool is

required.

4.3 Installation and removal of the 12-inch light fixture

Install the light fixture in a base

1. Carefully clean all contact surfaces of the light fixture and the base.
2. Put the O-ring gasket in the gasket track on the base.

Note

Not for class 2.

3. Connect the connector(s) of the light fixture to the base supply cable(s). Check that the A- and B-side are connected to

corresponding circuit if two connectors are used.

4. Place the connector under the light fixture and install in the base.
5. For an installation on bases, use a torque limiting box spanner of 16/17 mm, install and tighten the six fixing bolts or nuts

to a torque value according to specification, see

INTEROPERABILITY

. For other base manufacturers, refer to their

specifications.

Note

Do not use high speed for tightening, the recommended speed is 10

‑

40 rpm.

RELIANCE Inset Lights
Installation

12
Copyright

©

ADB Safegate, All Rights Reserved

«
...
20
21
22
23
24
...
»

Summary of Contents for RELIANCE AC

























































Reviews:

No comments

Related manuals for RELIANCE AC

Brand: S.R.Smith Pages: 43

Explore E3 E3009CD

Brand: Oceanled Pages: 4

Brand: Safavieh Pages: 2

Brand: SAC Pages: 2

Brand: Safavieh Pages: 2

Street Bar IP65 16x3W TW

Brand: Varytec Pages: 52

EPL-FL1524-LED-100

Brand: Larson Electronics Pages: 3

CLESSY 23.8600.85

Brand: O.N Pages: 9

Brand: DÖRR Pages: 16

Brand: Madrigal Pages: 5

Brand: Sirona Pages: 26

Brand: LIVARNO LUX Pages: 48

Brand: NANLITE Pages: 30

Brand: Safavieh Lighting Pages: 2

Cambria 203 LED

Brand: Cooper Lighting Pages: 2

Brand: NOMA Pages: 2

Poldina LD0280B3

Brand: Zafferano Pages: 5

FIX NEO Premium 4030 EF II

Brand: Fisheye Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands