ADB Safegate AXON FAA L-852A User Manual Download Page 17

Page: 17 / 98

3.0 Introduction

The all-in-one solution
The 8

‑

inch and 12-inch ranges are bi- or unidirectional low protrusion light-emitting diode (LED) inset light fixtures, available

in multiple versions:

Non-MON

Basic operation providing power only

MON (Fail-open) A LED light fixture with integrated fail open technology for CCR monitoring compatibility

Fixture with integrated ILCMS remote utilizing orthogonal frequency-division multiplexing (OFDM) technology

providing superior communication interfacing with LINC 360 System.

NOTICE

All our light fixtures are equipped with failed LED detection monitoring as required by FAA Engineering Brief 67.

Figure 1: 8- and 12-inch fixtures

Taxiway Inset 8"

2-bolt version

(4-bolt not shown)

Taxiway Inset 8" with

Style-1 jacketed cord set

Taxiway Inset 8" with

Style-6 cord set

axiway Inset 12"

Taxiway Inset 12" with

Style-1 jacketed cord set

Taxiway Inset 12" with

Style-6 cord set

Note

EQ light fixtures are not fail-open light fixtures. The monitoring as well as the control functionality is handled by the ILCMS system.

UM-5056, Rev. 1.0.17, 2022/12/08

Summary of Contents for AXON FAA L-852A

























































































Search results

Summary of Contents for AXON FAA L-852A

Reviews:

Brands by name

Popular brands

ADB Safegate AXON FAA L-852A, User Manual

Search results

Summary of Contents for AXON FAA L-852A

Reviews:

Brands by name

Popular brands