manualshive.com logo in svg

Adaptive AlphaXpress 8731, Installation And Maintenance Manual, Page: 27 / 56

Share
Download
Adaptive AlphaXpress 8731 Installation And Maintenance Manual Download Page 27

E

QUIPMENT

I

NSIDE

 

VIEW

AlphaXpress 8731 Sign Installation and Maintenance Manual (pn 1508610601 rev. A)

27

Controller #1 and #2

Figure 24.

Controller components identification.

Item

PCB label

Name

Description

A

JP7 TO JP11

Configures controller for RS422 on J6 for display modules (115.2 kbaud).

B

J6

RS485 PORT 1

• Controller #1 — connects to LED displays.
• Controller #2 — connects to light sensors #0, #1, and #2.

C

J5 A/INPUT

ANALOG INPUTS

Depends on application; see wiring diagram included with sign.

D

J4 D/INPUT

DIGITAL INPUTS

• Controller #1 — connects to power supply fail signals, and door status.
• Controller #2 — connects to power fail signals of power supplies.

E

S1

DIP SWITCHES

Serial addressing and sign controller configuration.

F

P1

RS232 PORT

RS232 COMM PORT 0 — not used because J3 is used.

G

JMP2 TO 
JMP6

Configures controller for RS422 on J3 for communication between controllers.

H

J3

RS422 PORT

Used to interface both sign controllers together.

I

J2

DIGITAL OUTPUTS

Used to control beacons (when installed).

J

JMP1

Configures controllers for DC power.

K

J1

POWER 
CONNECTOR

Connects to 12VDC power.

L

P4

RS232 PORT

Not used.

M

BAT1

CONTROLLER 
BATTERY

3V lithium battery (Panasonic CR2032 or equivalent).

A

B

C

D

E

F

G

H

I

J

R

K

L

N

O

P

S

M

Q

Summary of Contents for AlphaXpress 8731

























































Reviews:

No comments