Adaptec CDP-00278-01-A Page 119 User Manual Download | Manualshive

Page: 119 / 130

background image

RAID 6 Logical Drives

A RAID 6 logical drive—also known as dual drive failure protection—is similar to a RAID 5 logical drive
because it uses data striping and parity data to provide redundancy. However, RAID 6 logical drives
include two independent sets of parity data instead of one. Both sets of parity data are striped separately
across all disk drives in the logical drive.

RAID 6 logical drives provide extra protection for your data because they can recover from two
simultaneous disk drive failures. However, the extra parity calculation slows performance (compared
to RAID 5 logical drives).

RAID 6 logical drives must be built from at least four disk drives. Maximum stripe size depends on the
number of disk drives in the logical drive.

Unused Space = 150 GB

Disk Drive 1

Disk Drive 2

Disk Drive 3

Disk Drive 4

250 GB

250 GB

400 GB

400 GB

Drive Segment Size
(Smallest Disk Drive)

Disk Drive 2

Disk Drive 3

Disk Drive 4

Disk Drive 1

Unused Space = 150 GB

Disk Drives in Logical Drive

Based on the drive segment sizes used:

(P1 & P2)

RAID 6 Logical Drive = 500 GB plus parity

P2

1 P1 . . .

449

2 P2 . . .

P1

P1 3 . . .

500

P2 4 . . .

RAID 60 Logical Drives

Similar to a RAID 50 logical drive (see

RAID 50 Logical Drive

on page 118), a RAID 60 logical drive—also

known as dual drive failure protection—is built from eight disk drives configured as two or more RAID
6 logical drives, and stripes stored data and two sets of parity data across all disk drives in both RAID 6
logical drives.

Two sets of parity data provide enhanced data protection, and striping improves performance. RAID 60
logical drives also provide high data transfer speeds.

119

Proprietary and Confidential to PMC-Sierra, Inc.
Document No.: CDP-00278-01-A Rev. A, Issue:

maxView Storage Manager User's Guide

«
...
117
118
119
120
121
...
»

Summary of Contents for CDP-00278-01-A



































































































































Reviews:

No comments

Related manuals for CDP-00278-01-A

Brand: Avaya Pages: 20

APPLICATION STACK 2.0 RELEASE

Brand: Red Hat Pages: 26

NETWORK SATELLITE SERVER 4.0

Brand: Red Hat Pages: 80

NETWORK - USER REFERENCE GUIDE 3.1

Brand: Red Hat Pages: 78

NETWORK SATELLITE 5.1.0 - CHANNEL MANAGEMENT

Brand: Red Hat Pages: 300

PSB - ADMINISTRATORS GUIDE FOR RESELLERS

Brand: F-SECURE Pages: 48

Brand: E-Mu Pages: 42

Brand: Altigen Pages: 34

Brand: Focusrite Pages: 16

DIRECTOR MX 2004-GETTING STARTED WITH...

Brand: MACROMEDIA Pages: 68

Brand: Native Instruments Pages: 41

MOVI 4.0 - ADMINISTRATOR GUIDE 09-2010

Brand: TANDBERG Pages: 22

FREEFLOW 701P25032

Brand: Xerox Pages: 112

Brand: Canon Pages: 50

Brand: Ulead Pages: 66

VIDEOGRAPHICS LAB

Brand: Ulead Pages: 110

Brand: Ulead Pages: 125

Brand: Ulead Pages: 204

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands