1. Product Features
- Plastic alloy enclosure (light weight and durable)
- Relative/absolute measurement interc hange at any position
- With 2 built-in magnets on measuring surface
- Slope measurement in % and °
- Power-off automatically in 5 minutes
- Portable size, convenient to co-work with other measuring tools
2. Technical Parameters
1. Measuring range: 4x90°
2. Resolution: 0.05°
3. Accuracy: ±0.2°
4. Battery: 9V
5. Working temperature: 0°C ~40°C
6. Dimension: 57*57*30.5 mm
7. With 2 built-in magnets, with diameter 10 mm on measuring surface
8. N. Weight: 0.13kg
3. Operating Instructions:
1. Press the «ON/OFF» button, it turns on, and the LCD displays absolute hori-
zontal angle. «Level» is displayed on the screen. Press «ON/OFF» button again to
switch off the instrument.
2. If you lift left side of the instrument you will see arrow «▲» on the left side of the
display. On the right side of the display you will see arrow «▼» . It means the left
side is higher and right side is lower.
3. Put the instrument on the horizontal stand, and press the «ZERO» button, the
value returns to zero, and the read-out is the angle value measured relatively to the
horizontal stand. In this mode «Level» is not displayed.
4. Press «Hold/Tilt%» to hold value on the display. To continue angle measurement
press Hold/Tilt% button again.
5. Press «Hold/Tilt%» button for 2 sec to measure slope in %. To make angle mea-
surement in degrees, press and hold «Hold/Tilt%» button for 2 sec.
6. The magnets at the bottom allows the instrument to be attached onto iron ma-
terial measurement object. Press the «ZERO» button, reset the value to proceed
relative measurement.
4. Application:
Control and measurement of slope of any surface. It is used in wood processing
industry (especially in furniture manufacturing industry) for wood angle accurate
cutting; auto repair industry for tiring assembling angle accurate controlling; in ma-
chining industry for machine tool working angle accurate positioning; in woodwork;
when setting guides for gypsum board partitions.
5. Calibration
1) Press and hold ZERO button to turn on the calibration mode. Then press and
hold ON/OFF button. Calibration mode is activated and “CAL 1” is displayed. Place
the instrument on a flat and smooth surface as shown in the picture.
2) Press ZERO button once in 10 seconds. “CAL 2” wil be displayed. Rotate the instru-
ment by 90 degrees in clockwise direction. Place it on the right edge towards display.
WARRANTY DOESN’T EXTEND TO FOLLOWING CASES:
1. If the standard or serial product number will be changed, erased, removed or wil
be unreadable.
2. Periodic maintenance, repair or changing parts as a result of their normal runout.
3. All adaptations and modifications with the purpose of improvement and expansion
of normal sphere of product application, mentioned in the service instruction, without
tentative written agreement of the expert provider.
4. Service by anyone other than an authorized service center.
5. Damage to products or parts caused by misuse, including, without limitation, mis-
application or nrgligence of the terms of service instruction.
6. Power supply units, chargers, accessories, wearing parts.
7. Products, damaged from mishandling, faulty adjustment, maintenance with
low-quality and non-standard materials, presence of any liquids and foreign objects
inside the product.
8. Acts of God and/or actions of third persons.
9. In case of unwarranted repair till the end of warranty period because of damages
during the operation of the product, it’s transportation and storing, warranty doesn’t
resume.
For more information you can visit our website
WWW.ADAINSTRUMENTS.COM
or write the letter with your questions on
WARRANTY CARD
Name and model of the product ___________________________________________
Serial number ________________date of sale__________________
Name of commercial organization ________________stamp of commercial organization
Warranty period for the instrument explotation is 24 months.
During this warranty period the owner of the product has the right for free repair of his
instrument in case of manufacturing defects.
Warranty is valid only with original warranty card, fully and clear filled (stamp or mark of
the seller is obligatory).
Technical examination of instruments for fault identification which is under the warranty, is
made only in the authorized service center.
In no event shall manufacturer be liable before the client for direct or consewuential dam-
ages, loss of profit or any other damage which occur in the result of the instrument out
-
age.
The product is received in the state of operability, without any visible damages, in full
completeness. It is tested in my presence. I have no complaints to the product quality. I
am familiar and agree with the conditions of warranty service.
Purchaser signature _______________________________
Before operating you should read service instruction!
If you have any questions about the warranty service
and technical support contact seller of this product
Operating manual
INCLINOMETER ProDigit RUMB
3) Press ZERO button once in 10 seconds. “CAL 3” wil be displayed. Rotate the
instrument by 90 degrees in clockwise direction. Place it on the upper edge towards
display.
4) Press ZERO button once in 10 seconds. “CAL 4” wil be displayed. Rotate the
instrument by 90 degrees in clockwise direction. Place it on the left edge towards
display.
5) Press ZERO button once in 10 seconds. “CAL 5” wil be displayed. Rotate the
instrument by 90 degrees in clockwise direction. Place it on the lower edge towards
display.
6) Press ZERO button once in 10 seconds. “PASS” wil be displayed. After a while
“0.00 degrees” will be also displayed. The calibration is over.
Manufacturer: ADAINSTRUMENTS Address: WWW.ADAINSTRUMENTS.COM
Pro
Digit
RUMB
