8
9
Troubleshooting
No outdoor sensor
reception
no bars
If the wireless signal indicator shows no bars:
• Relocate the display unit and/or the outdoor sensor.
The units must be within 165 ft (50 m) of each other.
• Make sure both units are placed at least 3 feet (.9 m)
away from electronics that may interfere with the
pbk^e^ll\hffngb\Zmbhg!ln\aZlMOl%fb\khpZo^l%
computers, etc).
• Use standard alkaline batteries (or lithium batteries in
l^glhkpa^gm^fi^kZmnk^bl[^ehp&-?(&+)<"'=hghm
nl^a^Zor]nmrhkk^\aZk`^Z[e^[Zmm^kb^l'GHM>3Bm
may take up to 20 minutes for display unit and sensor
to synchronize after batteries are replaced.
Outdoor
temperature
akÛYk`af_gj
showing dashes
Flashing of the outdoor temperature is generally an
indication of wireless interference.
1. Bring both the sensor and display unit indoors and
remove at least one battery from each.
2. Reinstall the battery in the outdoor sensor.
3. Reinstall the battery in the display unit.
-'E^mma^ngbmllbmpbmabgZ\hnie^_^^mh_^Z\ahma^k
for about 20 minutes to gain a strong connection.
Inaccurate
temperature
• Make sure both the display unit and sensor are
placed out of direct sunlight and away from any heat
sources or vents (see page 6).
Display screen
not working
• Check that the batteries are installed correctly.
Batteries may need to be replaced.
If your AcuRite product does not operate properly after trying
the troubleshooting steps, visit www.AcuRite.com or call
(877) 221-1252 for assistance.
Care & Maintenance
Display Unit Care
<e^ZgpbmaZlh_m%]Zfi\ehma'=hghmnl^\Znlmb\\e^Zg^klhkZ[kZlbo^l'D^^i
away from dust, dirt and moisture. Clean ventilation ports regularly with a
gentle puff of air.
Outdoor Sensor Care
<e^ZgpbmaZlh_m]Zfi\ehma'=hghmnl^\Znlmb\\e^Zg^klhkZ[kZlbo^l'
Kh][aÚ[Ylagfk
TEMPERATURE RANGE
Outdoor: -40
º
F to 158
º
F; -40
º
C to 70
º
C
Indoor: 32
º
F to 122
º
F; 0
º
C to 50
º
C
WIRELESS RANGE
165 ft / 50 m
depending on home construction materials
WIRELESS FREQUENCY
POWER
=q:::ZedZebg^[Zmm^kb^l
Sensor: 2 x AA alkaline or lithium batteries
DATA REPORTING
30 second updates
FCC Information
This device complies with part 15 of FCC rules. Operation is subject to the following two conditions:
*&Mabl]^ob\^fZrGHM\Znl^aZkf_nebgm^k_^k^g\^%Zg]
2- This device must accept any interference received, including interference that may cause undesired operation.
P:KGBG@3<aZg`^lhkfh]bÛ\Zmbhglmhmablngbmghm^qik^llerZiikho^][rma^iZkmrk^lihglb[e^_hk\hfiebZg\^\hne]ohb]ma^
nl^klZnmahkbmrmhhi^kZm^ma^^jnbif^gm'
GHM>3Mabl^jnbif^gmaZl[^^gm^lm^]Zg]_hng]mh\hfierpbmama^ebfbml_hkZ<eZll;]b`bmZe]^ob\^%inklnZgmmhIZkm*.h_ma^?<<
rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equip-
ment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
\Znl^aZkf_nebgm^k_^k^g\^mhkZ]bh\hffngb\Zmbhgl'Ahp^o^k%ma^k^blgh`nZkZgm^^maZmbgm^k_^k^g\^pbeeghmh\\nkbgZiZkmb\neZk
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
<hglnemma^]^Ze^khkZg^qi^kb^g\^]kZ]bh(MOm^\agb\bZg_hka^ei'
GHM>3Ma^fZgn_Z\mnk^kblghmk^lihglb[e^_hkZgrkZ]bhhkMObgm^k_^k^g\^\Znl^][rngZnmahkbs^]fh]bÛ\Zmbhglmhmabl^jnbif^gm'
Ln\afh]bÛ\Zmbhgl\hne]ohb]ma^nl^kZnmahkbmrmhhi^kZm^ma^^jnbif^gm'
Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation of the device.
433.92MHz
This device complies with Industry Canada’s licence-exempt RSSs.
Cet appareil est conforme aux CNR exemptes de licence d'Industrie Canada . Son fonctionnement est soumis aux deux conditions suivantes :
( 1 ) Ce dispositif ne peut causer d'interférences ; et
( 2 ) Ce dispositif doit accepter toute interférence , y compris les interférences qui peuvent causer un mauvais fonctionnement de l'appareil.
