background image

 

actiLib Library 4U  

– User and Service Guide    

 

 

Page 13 of 103 

 

 

Product description (overview) and features 

The actiLib Library 4U  provides a compact, high-capacity, low-cost solution for simple, unattended 
data backup. This unique design houses up to 48 tape cartridges in a compact 4U form factor with 
easy access to tape cartridges via two removable magazines and a mailslot. The magazines can hold 
up to twelve (left magazine including mail slot) and nine (right magazine) cartridges. 
 
The library can support one to four half height tape drives, or tow full height tape drive. The library 
occupies one SCSI target address (for the single drive version) and uses dual LUNs for the tape drive 
and library robotic. 
 
The actiLib Library 4U  is compatible with most operating systems and environments that support the 
SCSI interface. However, the library requires either direct support from the operating system or a 

compatible backup application to take full advantage of its many features.  
 

 

Figure 1 actiLib Library 4U   front and rear view 

Particular emphasis of the actiLib Library 4U   family includes: 

 

Platform of  tape Librarys

 -

 independent of tape and drive form factors 

 

Broad level of connectivity

 

-

 SCSI, FC1, FC2, FC4, and SAS  

 

Expandability

 - magazines, drive sleds, and extra controller/converter cards can be added in 

the field as available 

 

Technology upgrade

 

-

 customer can upgrade tape drive technologies (e.g. LTO5 to LTO6) in 

the field 

 

Service friendly design

 - drive, power supply and Library controller are accessible from the 

back of the unit allowing for quick replacement 

 

Best in class cartridge and drive density

 - packing in as many or more cartridges in the 

standard rack height 4U as most other Libraries on the market 

 

Maximum up time

 - through advanced error handling and recovery capability 

 

Summary of Contents for actiLib Autoloader 4U








































































































Reviews: