background image

www.acti.com

 

 

KCM-8111 Hardware User’s Manual 

                 

Safety Instructions 

 

Don’t use the power supply with other voltages 

This device is likely to be damaged or damage other equipments / personnel, if you use a 

power supply with different voltage than the one included with this device. All warranty of this 

product will be voided in the situations above. 

 

Don’t open the housing of the product 

 

Cleaning 

Disconnect this video product from the power supply before cleaning. 

 

Attachments 

Do not use attachments not recommended by the video product manufacturer as they may 

cause hazards. 

 

Water and Moisture 

Do not use this video product near water, for example, near a bathtub, washbowl, kitchen sink, 

or laundry tub, in a wet basement, or near a swimming pool and the like. 

 

Don’t use accessories not recommended by the manufacturer 

Only install this device and the power supply in a dry place protected from weather   

 

Servicing   

Do not attempt to service this video product yourself as opening or removing covers may 

expose you to dangerous voltage or other hazards. Refer all servicing to qualified service 

personnel. 

 

Damage Requiring service 

Disconnect this video product from the power supply immediately and refer servicing to 

qualified service personnel under the following conditions. 

1)  When the power-supply cord or plug is damaged 

2)  If liquid has been spilled, or objects have fallen into the video product. 

3)  If the video product has been directly exposed to rain or water.   

4)  If the video product does not operate normally by following the operating Instructions in 

Summary of Contents for KCM-8111
















Reviews: