background image

www.acti.com

Hardware Manual 

                 

37 

How to Connect Audio Devices 

The camera comes with audio input / output jacks to connect a microphone or speaker to the 

camera. The audio jacks are covered with a rubber protection. 

If using an audio input device, such as a microphone with a built-in amplifier, connect the device 

to the 

Audio Input

 jack (RED) of the camera. If using an audio output device, such as a speaker, 

connect the device to the 

Audio Output

 jack (GREEN) jack of the camera. 

If the camera is installed outdoors, be sure o wrap the audio connectors with Waterproof tape 

(can be purchased in hardware stores). 

DISCLAIMER:

 ACTi will not be responsible for damaged cameras due to water leakage caused 

by improper waterproofing of cables. 

 

NOTE 1:

 

Make sure that the connected audio input device has a built-in amplifier. Connecting an 

ordinary microphone will dwarf sounds and will result in inaudible recording. 

NOTE 2:

 If the audio connectors will not be used, leave the rubber caps on to avoid water and 

dust from entering the connectors.   

 

 

 

Audio Input Jack 

Audio Output Jack 

Audio Device 

Summary of Contents for B916


















































Reviews: