ACTi A713 Firmware Manual Download Page 113

Page: 113 / 115

112

Speed by Zoom

This function allows the camera to adjust the pan/tilt speed automatically by the

internal algorithm when the zoom ratio is changed. The rotating speed will

become slower as the zoom ratio gets larger. Click the <Set> button to save the

setting.

Auto Calibration (Servo Feedback)

Integrating Servo Feedback technology, the camera would calibrate and

precisely return to the previous position without stalling when the deviation of

dome pivot is detected. Select <On> and click the <Set> button to activate the

setting.

Set Pan Zero

Click the <Set> button to set the camera

’s currently shooting position as the

start point for panning (0 degree).

2.7

Logout

Click on the tab <

Logout

> on the top of the page, and the login window will

popup. This enables login with another username.

Summary of Contents for A713




















































































































Search results

Summary of Contents for A713

Reviews:

Related manuals for A713

Brands by name

Popular brands

ACTi A713, Firmware Manual

Search results

Summary of Contents for A713

Reviews:

Related manuals for A713

Brands by name

Popular brands