ACTi A713 Firmware Manual Download Page 106

Page: 106 / 115

105

Step 3.

Assign a number for the current position from the drop-down Number

List (click <PrePage> or <NextPage> button to reach number 1 to 256),

and enter its descriptive name.

Step 4.

Click the <Set> button to save the settings.

Preset Go

To have the camera move to a specified preset position, please select the

Preset Point from the drop-down Preset list (click <PrePage> or <NextPage>

button to reach preset number 1 to 256). Then the camera shall move to the

target position.

2.6.2

Cruise

The Cruise Programming can be found under this path:

PTZ> Cruise

The camera supports up to 8 Cruise Paths. Please follow the instructions below

for Cruise Path setup.

Cruise Setting

Refer to the steps below to setup a Cruise Path.

Step 1.

Select a path number from the drop-down list.

Step 2.

Move the cursor to the live view pane, and move the camera to a desired

view (PTZ controls) as the start point of a Cruise Path.

Step 3.

Click the <Set> button of <Record Start> and start programming the

Cruise Path via PTZ controls.

Step 4.

When finishing programming, click the <Set> button of <Record End> to

complete recording the Cruise Path.

Cruise Run

Select the specified Cruise Path from the drop-down list, click the <Run> button,

and then the camera will start touring around as recorded.

To view the camera touring in full screen mode, please move the cursor onto the

live view pane, right-click and left-click to select

“Fullscreen”. Then users can

view the camera navigation in full screen.

To stop running a Cruise Path, simply move the cursor to the live view pane and

move the camera in any direction.

Summary of Contents for A713




















































































































Search results

Summary of Contents for A713

Reviews:

Related manuals for A713

Brands by name

Popular brands

ACTi A713, Firmware Manual

Search results

Summary of Contents for A713

Reviews:

Related manuals for A713

Brands by name

Popular brands