ACTi A713 Firmware Manual Download Page 103

Page: 103 / 115

102

Preset Run

Type the Preset Point number into the Preset field, click on

, and the

camera will turn to the appointed point.

2.5.2 Sequence

The Sequence setting can be found under this path:

Pan Tilt> Sequence

The Sequence function supports eight Sequence Lines. Each Sequence Line

consists of 64 Preset Points. Please refer to the instructions below to program a

Sequence Line.

NOTE:

Before setting this function, users must pre-define at least two

Preset Points.

Sequence Setting

⚫

Sequence Line

The Sequence Lines are numbered from 1 to 8. Select a Sequence Line

from the drop-down menu. Then click on

to enter the setup

page.

⚫

Sequential Preset Points Setting

Please setup each Preset Point of the programmed Sequence Line in
order, assigning a Preset Point from the “NO.” list for the specified

number of Preset Point and entering Dwell Time (0 sec. to 255 sec.) into

the corresponding fields. Click on <Save> when finished.

⚫

Sequence Reset

To reset the sequence setting of each line, please click on <Reset> on

the setup page. Then click on

on the left to refresh the page in

order to enter the new settings.

Summary of Contents for A713




















































































































Search results

Summary of Contents for A713

Reviews:

ACTi A713, Firmware Manual, Page: 103 / 115

Search results

Summary of Contents for A713

Reviews: