ACT5 DIGITAL KEYPAD
30 SECOND PROGRAMMING GUIDE
(for typical
system
)
1.
Enter Programming
Mode
.
Press X
button
followed
by
the
programming
code (9999)
The
LED
will
flash
Ambe
r
2.
Change User
1
code
.
Press
0,
then
1
followed
by
the
new
user
1
cod
e
(four
di
gits
)
3.
Change Programming
Code
.
Press 0,
then
followed
by
the
new
progr
am
-
min
g co
de
(fo
ur
d
igits)
.
4.
Set Desired
Relay
Active
Tim
e
.
Press
2,
th
en
0.
A
llow
th
e bu
zzer to
so
und for
the
des
ired
p
eriod
. Pre
ss
to
stop –
this
period
is now
programmed
into
the
relay
timer
.
5.
Exit Programmi
ng
Mo
de.
Press the
X
button.
The
LE
D w
ill be
Re
d.
The keypad
is
now
ready
for
normal
use
.
Note:
T
he
k
eyp
ad
may
b
e ret
ur
ne
d to
it
s factory
d efault
condition
at
any
time
by
entering
the
p
ro
-
grammin
g mo
de
a
nd p
ress
in
g t
he
three
ti
me
s.
Restoring F
actory
Default
s
(From Programming
Mode
)
(Factory
Defaults
Restored
&
Keypad
exits
programming
mode
)
If the
progr
a mmi
ng
co
de
ha
s b
een
forgotte
n.
1
.
Remove the
power
from
the
unit
.
2
.
Remove link
LK1
.
3
.
Apply
p
ow
er to
un
it.
4
.
Replace li
nk
LK1
.
5
.
Remove power
again
.
6
.
Restore power
and
proceed
with
programming
.
Note:
The keypad
will
not
operate
correctly
with
out
LK1
in
place
.
Incorrect Code
Lockou
t
When
three invalid
codes have
been entered
in a
row. The
keypad will
enter lockout
mode
for
20
seconds.
Du
rin
g t
his
time,
th
e re
d i
ndicator
will
fla
sh a
nd all
us
er co
ded
w
ill b
e i
nactive
.
ACT5 D
ig
ita
l Ke
ypad Pr
ogramm
in
g
To e
nter
p
rogrammin
g mo
de
:
Press
th
e X
bu
tton
follo
wed
b
y t
he
en
gin
eerin
g co
de
(in
itially al
l 9999) Th
e
LED will
flash
Amber
while
in
programming
mode
.
If
X is
pressed
at
an
y
tim
e o
r no
k
ey
is
p
ress
ed
w
ith
in
30
seconds,
programming
mode
is
exited
.
Changing
Cod
es:
(from programming
mode
)
Enter
0
(Change codes
)
0
-9
,
(user
number
0
-9
,
=
programming
code
)
000
0-999
9
(4 digit code
–
0000 d
elete
s us
er)
Default
user
codes
:
Programming =
9999,
User
1
=1234
,
A
ll ot
her
s in
active.
Setting the
Relay
active
time
:
(from programming
mode
)
Enter 2
(Set
Relay
active
Time
)
0
(Rel
ay T
im
er)
{Buzzer
sound
s indicating
timing
…
wait required
period
}
(Stop
timing)
{Buzzer
stops
—
tim
er s
et}
IMPORTANT
As with any access control system, always ensure that there is
an alternate means of escape in the event of the unit failing to
operate due to power loss or in the event of fire.
Unit
C1 South City Business Centre
,
Tallaght, Dublin 24,
Ireland.
Tel: 353-1-46
6 2570
Fax: 353-1-4
52 0427
Copyright
2003 Access Control Technology Ltd.
(18-00001-27)
INSTALLATION NOTES
•
Always remember to factory default the controller before
you start programming.
•
Always remember to place the supplied Varistor
across the terminals of the door strike coil to protect
the relay contacts.
•
Never use the onboard relay to switch AC mains voltage.
An external relay isolated electrically from the ACT5
should be used for this purpose.
•
Don’t forget to change the programming code to some-
thing known only to yourself.
For full details on the ACT product range and a list of distributors,
Visit our website www.accesscontrol.ie
