ACS Fluxicont FP Manual Download Page 10

ACS-CONTROL-SYSTEM GmbH

 l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]

10

Switch output

Version type GA - PNP switch output

An inductive loads at the pnp switch output, e.g. relays or contactors may only be used with a free-

wheeling diode or a RC protection circuit to avoid high voltage peaks.

The load at the PNP switch output will be connected to the teL of the supply voltage by a 

semiconductor switch contactless and by this bounce-free.

At an activated switching state a positive signal near supply voltage is feed to the output.

At deactivated switching state and at failure of supply voltage the semiconductor switch is shut off.

The PNP switch output is current limited to 0,5 A and is overload and short circuit protected.

The device is suitable for non-coincidence use. Using both outputs the NO and NC outputs leads 

contrary states at trouble-free operation.

In the case of failure or at wire break both electronic switches are opened.

By using a two-channel evaluation, besides the flow monitoring also a function dependent monitoring 

of the sensor can be realized.

Version type WB - relay output

Inductive loads at the relay contacts, e.g. auxiliary contactors or magnetic vents may only be used 

with a free-wheeling diode or a RC protection circuit to avoid high voltage peaks.

The load at the relay output will be connected to the terminal L/+L of the supply voltage.

At an activated switching state the supply voltage of the connection terminal L/+L is feed to the 

output.

At deactivated switching state the output is voltage and potential-free.

The device is suitable for non-coincidence use. Using both outputs the NO and NC outputs leads 

contrary states at trouble-free operation.

In the case of failure or at wire break the terminal NO is potential-free and the terminal NC is 

connected to the terminal L/+L.

By using a two-channel evaluation, besides the flow monitoring also a function dependent monitoring 

of the sensor can be realized.

Summary of Contents for Fluxicont FP















Reviews: