manualshive.com logo in svg

Acromag Vertu Series, Instruction Manual, Page: 32 / 47

Share
Download
Acromag Vertu Series Instruction Manual Download Page 32

Vertu Series VPM3000 Process Meters & Temperature Transmitters 

Instruction Manual 

32

 

DisplayWizard

 

Software 

Note:

 Vertu meter is not powered from USB connection and 

requires external power to be programmed. 

Remote Programming

DisplayWizard software allows all setup parameters to 

be programmed remotely from a PC and saved to a 

file for reporting or programming other meters. 

Data Acquisition

DisplayWizard software provides a convenient way to 

collect the data generated by the Vertu Model 

VPM3000 serial output. The user can select the log-

ging time interval. Data can be written to a file, which 

can then be imported into a spreadsheet or other ap-

plication. 

Monitoring 

DisplayWizard software can be used to monitor up to 

100 Vertu meters on a PC. The user can set a custom 

meter identification, such as Tank 1 to display on the 

screen as well as engineering units, such as feet. The 

screen shot below shows DisplayWizard software 

monitoring level in six storage tanks: 

Monitoring System Parts 

The following table illustrates the parts needed to 

monitor 10 Vertu meters: 

Quantity 

Model

 

Description

 

10 

APMA7422 

Vertu RS-485 

Serial Adapter 

1 

ACC1003

 

Isolated USB to 

RS-485 Converter 

DisplayWizard Installation 

1. Download DisplayWizard software from CD
2. Read instructions & copy serial # of desired

DisplayWizard version

3. Download Installation file to computer
4. Double-click installation file to open it
5. Double-click 

Setup.exe

 to begin installation

6. Follow on-screen instructions

Running DisplayWizard the First 

Time

 

The first time DisplayWizard is run it is necessary to 

set up the serial communication settings of the pro-

gram. Select the communication port and the baud 

rate of the meter(s) connected. 

Note:

 The selected baud rate in DisplayWizard and the me-

ter(s) baud rate must be the same. Otherwise a com-

munication error will occur. 

Enable Meter and Select Meter 

Address 

The actual meter address is set up at the meter using 

the front panel buttons. The location where a meter is 

displayed is selected on DisplayWizard Main window. 
To enable or select a meter with a different serial  

address: 

1. Right-click on the screen location of meter.
2. Click on 

Enabled

, if meter is not yet enabled.

3. Click on 

Change Address

.

4. Select meter address to display in this location.

Summary of Contents for Vertu Series
















































Reviews:

No comments