manualshive.com logo in svg

Acromag microBlox Series, User Manual, Page: 7 / 29

Share
Download
Acromag microBlox Series User Manual Download Page 7

microBlox® Transmitter/Alarm Carrier 

                        Model uBTA-H-1MR/uBTA-H-1SR/uBTX-H-1 

 

 

Acromag, Inc. Tel: 248-295-0880  

 

          - 7 -                                   

http://www.acromag.com  

- 7 - 

https://www.acromag.com 

 

 

DIN Rail Mounting & Removal 

 
 

 
When removing the carrier from the DIN rail, it is recommended that your uB input 
module be unplugged from the top of the carrier first.  Refer to the figure below for 
attaching and removing the carrier from the DIN rail.  The DIN rail clip located on 
the bottom side is spring-loaded.  The opposite rounded edge at the bottom of the 
top side allows you to tilt the unit upward to lift it from the rail while prying the 
spring clip back with a screwdriver along the bottom as shown below.   

 
To attach the carrier to T-type DIN rail, angle the top of the unit towards the rail and 
place the top groove of the carrier over the upper lip of the DIN rail.  Firmly push 
the unit downward towards the rail until it snaps into place. 

 
To remove it from the DIN rail, first separate the input and power terminal blocks 
(TB1-TB3) from the bottom side of the module to create clearance to the DIN 
mounting clip. You can use a screwdriver to pry the pluggable terminals out of their 
sockets.  Next, while holding the carrier in place from above, insert a screwdriver 
along the bottom side path of the carrier to the DIN rail clip and use it as a lever to 
force the DIN rail spring clip down, while pulling the bottom of the carrier outward 
until it disengages from the rail.  Then simply tilt the carrier upward to lift it off the 
rail. 

 

 

 

 

Summary of Contents for microBlox Series






























Reviews:

No comments