manualshive.com logo in svg

Acromag microBlox Series, User Manual, Page: 11 / 29

Share
Download
Acromag microBlox Series User Manual Download Page 11

microBlox® Transmitter/Alarm Carrier 

                        Model uBTA-H-1MR/uBTA-H-1SR/uBTX-H-1 

 

 

Acromag, Inc. Tel: 248-295-0880  

            - 11 -                                   

http://www.acromag.com  

- 11 - 

https://www.acromag.com 

 

 

Input Connections, BLE Jumper, and CJC Jumper

 

 

 

A single MicroBlox input module plugs directly into the front panel opening of this carrier and is retained by 
an internal spring clip.  Input connections are wired to the carrier terminals in the same fashion as input 
connections to uB modules when mounted on uB back-panels (refer to your uB manual per specific model).  
Wired jumpers are also used on this carrier to enable BLE linking and CJC connections, and have the same 
effect as setting the standard uB backpanel BLE and CJC switches (a jumper present equals switch ON). 
 

 

 
Observe proper polarity when making input connections.  TB1 of this carrier connects INPUT ±, while TB2 
connects EXC ±.  The last two terminals of TB1 are for installation of a CJC jump-wire to enable CJC for some 
input models (see table above) and this has the equivalent function of the CJC DIP switch of uB back-panels.  
Similarly, TB2 includes two jumper terminals to enable Bluetooth wireless technology linking (refer to your uB 
model instructions) and adding this jumper is equivalent to switching the BLE DIP switch of uB back-panels 
ON.  Refer to the table above and add or remove this jump-wire between the last two terminals of TB1

—

some 

modules will require a CJC connection, while others do not.   Installing a jump wire between the first two 
terminals of TB2 will enable you to link to the installed uB module using Bluetooth wireless technology from 
your smartphone or tablet (remove this jumper to block access).  Refer to the figure above and your specific 
uB module manual (see below) for info on making input connections, or for information about CJC jumper 
installation, or enabling Bluetooth wireless technology linking:   

 

 

REFERENCE 

DESCRIPTION 

8501-037 

uB31 & uB41 Voltage Input User Manual 

8501-040 

uB30 & uB40 mV Input User Manual 

8501-041 

uB32 DC Current Input User Manual 

8501-042 

uB42 DC Current Input w/2-Wire Excitation User Manual 

8501-043 

uB34 2/3-Wire & uB35 4-Wire RTD Input User's Manual 

8501-044 

Introduction to Agility Configuration Tool for microBlox® 

8501-047 

uB37 & uB47 TC Input User Manual 

8501-050 

uB04/uB08/uB16 Back-Panel User Manual 

 

 

 

Summary of Contents for microBlox Series






























Reviews:

No comments