ACO Quatrix-K 620368 Operating Manual Download Page 28

28

Product description

4.5.1  Function in normal operation

In normal operation mains voltage 
persists, the green LED 1 (1) lights up 
permanently and the buzzer is out. The 
operating seal (8) and the emergency 
seal (9) are opened. Arriving wastewater 
from drainage objects (WC, shower, 
washing basin) can drain off unobst-
ructedly. 

4.5.2  Automatic antiflood protection system

In the case of backflow, pipe fills up with 
wastewater from the public sewers. The 
generating back pressure is handed on 
to the pressure sensor integrated in the 
control by means of the pressure hose 
(11). For the unobjectionable function of 
the pressure sensor, permanently rising 
laying of pressure hose (11) is of utmost 
importance.

If the admissible filling level is exceeded, the red LED 2 (2) lights up permanently. 
The control causes the operating seal (8) to be automatically closed by means of 
the elecrtric motor (10) with a delay of 3 seconds. The yellow LED operating seal 
(3) flashes during the closing lasting for 17 seconds. The delay time of 3 seconds 
avoids a backflow alarm in the case of short-time splashes.

If the operating seal (8) is obstructed during its run in its defined final position          
(e. g. by deposits), then it opens and tries to close for a second time automatically. 
If the operating seal (8), however, cannot reach its defined final position, a motor 
fault is signalled. The red LED 4 (4) lights up permanently, and at the same time, an 
interval tone sounds through the buzzer (7).

If the operating seal (8) is closed, the yellow LED 3 (3) lights up permanently and a 
permanent tone sounds through the buzzer (7).

If the admissible filling level in the pipeline is undercut, the red LED 2 (2) goes out. 
The control causes the operating seal (8) to be opened automatically with a delay of 
30 seconds. During the opening, the yellow LED 3 (3) flashes. After the operating 
seal has opened completely, the permanent buzzer sound goes out.

The delay time of 30 seconds prevents a premature opening of the operating seal 
(8) in the case of short-time relief of backflow situation.

Summary of Contents for Quatrix-K 620368













































































Reviews: