ACME NEBULA Page 16 User Manual Download | Manualshive

Page: 16 / 20

background image

15

D

6. Troubleshooting

Following are a few common problems that may occur during operation. Here are some

suggestions for easy troubleshooting:

A. The unit does not work, no light and the fan does not work

1. Check the connection of power and main fuse.

2. Measure the mains voltage on the main connector.

3. Check the power on LED.

B. Not responding to DMX controller

1. DMX LED should be on. If not, check DMX connectors, cables to see if link properly.

«
...
14
15
16
17
18
...
»

Summary of Contents for NEBULA





















Reviews:

No comments

Related manuals for NEBULA

Brand: BOXLIGHT Pages: 44

Brand: Ubiquiti Pages: 14

LIGHTSTYLE LS-7

Brand: Runco Pages: 100

Brand: Remaco Pages: 3

Brand: Barco Pages: 163

Brand: Dukane Pages: 106

QGD(7:1) R9840030

Brand: Barco Pages: 5

Brand: Panasonic Pages: 12

Brand: Panasonic Pages: 11

Brand: Panasonic Pages: 12

Brand: Panasonic Pages: 74

Brand: Panasonic Pages: 72

Brand: Knoll Pages: 28

Brand: Cirrus Screens Pages: 7

Brand: Cirrus Screens Pages: 10

Brand: Mitsubishi Pages: 2

Brand: IBM Pages: 80

Brand: Derksen Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands