background image

 

DANGER!

 

All electrically operated tools should be grounded and hooked up to a ground 

fault protection system.  
  

All gasoline or petrol tools must be used in an outside environment. Never inside or in a 

confined area.  
  

Accumulation of fumes or gases will cause serious injury or death.  

  

Be vigilant and very attentive to the work being performed and to your work area.  
Never operate a tool or saw when you are tired, fatigued or stressed.   
Follow all the safety recommendations.  
Play it safe, your health and safety are your most important asset.  

  

NEVER

 exceed the manufacturer recommended pressure rating and gallons per minute  

(GPM) specification or the electric power requirements of the motor.  

 

 

NEVER

 exceed the manufacturer recommended operating speed.                                                        

  

Make certain that the saw is in the neutral position before starting the hydraulic power 

supply. and that the previous instruction on the visual inspection of the tool has been 
carried out.  
  

Remove any material, debris, water accumulation, slurry or any other foreign objects 

from the work area that could prevent you from safely operating the tool.  

The cutting operation may produce sparks when embedded steel is encountered in the 

concrete being cut. No flammable material or fluid should be in your work area.

 DO 

NOT 

operate the saw in a confined space or an area where a spark could produce an 

explosion.  
  

Always be alert and vigilant.   

 

 

DO NOT

 

use the saw or the tool other than its intended application.   

  

Cut in step not to overload the tool to prevent overheating, damage to the motor or to 

put too much stress on the blade.  
 

 

DO NOT

 

apply too much pressure to the tool and maintain a firm grip at all times.  

  

Disconnect all power and water supply at the completion of your work.  

  

DO NOT

 

leave an un-attendant tool hook to the power supply.   

 

  

Clean the tool completely    

 

Summary of Contents for HS24H10











Reviews: