ATV/Snowmobile/Motorcycle/Scooter Heated Grips
ACE-HG20/21/21T User Manual
Thanks for purchasing our heated grips. For smooth installation, we recommend you read the guide carefully and
follow the steps below. During installation, please be careful not to damage the wiring or pull wire out of the
terminals in the multipin plugs. If you have any doubts about the installation then please contact your grips supplier
for advice or arrange for professional installation.
Plug and play adaptor cables have been developed for some vehicle. Check with your grip supplier which they can
offer.
There are three versions of the grips as follows:
ACE-HG20 (
Motorcycle/ Scooter
): 7/8” handlebars with twist grip throttle
ACE-HG21 (
ATV/Snowmobile/PWC
): 7/8” handlebars with thumb throttle
ACE-HG21T: 7/8” handlebars with thumb throttle including a thumb warmer
** PLEASE NOTE THE FOLLOWING SAFETY INFORMATION **
•
DO NOT HOLD THE GRIPS WITH BARE HANDS! ALWAYS WEAR GLOVES TO AVOID BURNS!
•
SWITCHING THE GRIPS ON FOR MORE THAN A FEW SECONDS IF NOT FITTED TO THE
HANDLEBARS WILL CAUSE DAMAGE TO THE GRIPS AND MAY WARP THE INNER TUBE
•
THE CONTROL BUTTON IS AN ELECTRONIC MICROSWITCH AND ONLY REQUIRES A GENTLE
PRESS. PLEASE DO NOT TRY TO PULL THE BUTTON OUT TO CLEAN IT, DOING SO WILL
DESTROY THE SILICONE AND IT WILL NOT BE POSSIBLE TO REINSTALL THE BUTTON.
COMPONENTS
1
×
Left Grip
with temperature controller button.
1
×
Right grip
.
1
×
Thumb warmer kit (ACE-HG21T only)
1
×
Connecting wire or bike specific plug and play cable.
2
×
Cable tie
2
×
Bar-end cap
FEATURES
!
ACEWELL grips fit any 7/8” / 22mm handlebars to work with existing twist grip throttle tubes (ACE-HG20) or
thumb throttle (ACE-HG21).
!
Push button temperature controller and power level display built into left grip allows an easy installation and no
need for additional switches.
!
5 levels of grip heat temperature with fast-heat at power on.
!
5 color illumination of the control button to indicate selected temperature.
!
The integrated control/display module keeps the original look of the bike but still allows full functionality of the
grips.
!
Classic slimline design which suits all types of motorcycle, scooter, ATV, PWC and Snowmobile.
!
Optional thumb heat pad available.
!
Hard wearing and anti-slip silicone outer layer giving soft but durable texture.
!
Low voltage detection - the grips automatically switch off to help protect against a flat battery
!
Simple installation with minimal wiring and detailed fitting instructions.
INSTALLATION & WIRING
ACE-HG20
& HG-21
1. Use the appropriate tool to remove the existing grips.
Clean the handlebars and throttle tube as applicable with solvent and ensure the bars are free of residue and glue.
2. Slide the Right grip onto throttle sleeve (HG20) or handlebar (HG21) and then the Left grip onto the handlebar.
Apply Epoxy into the handlebar or throttle sleeve to hold the grips securely in place.
Align the grips so that the cables point downwards and the control switch (button) can be easily pressed with your
thumb
3. Connect the plug and play cable or the power tails to the left grip. If using the power tails then the black wire
should connect to negative (battery -) and red wire to positive (+12v)
The grips feature an automatic power off function to save your battery so they can be connected to either an
ignition live or directly to the battery depending on your preference
4. Connect the Right twist throttle grip to the Left grip.
5. After installation, swing the handlebar left to right to ensure nothing obstructs the movement.
ACE-HG21T
Follow steps 1-3 above
4. The HG21T includes a thumb warmer.
5. Use solvent to clean the thumb throttle, remove the backing paper from the heater and stick to the thumb throttle
using the self-adhesive pad.
6. Cover the heat pad with the supplied heat shrink tubing, and shrink into place using a hot air gun or flame.
7. Plug the thumb heater inline between the left and right grips
8. After installation, swing the handlebar left to right to ensure nothing obstructs the movements.
