![background image](http://html.mh-extra.com/html/acer/veriton-3000/veriton-3000_service-manual_6262104.webp)
72
Chapter 4
NOTE: Ensure that the hard disk drive is configured correctly in BIOS Setup and that the cables/jumpers are set
correctly before diagnosing any hard disk drive problems.
Hard disk drive test failed.
1. Make sure that the hard disk drive is not write-protected.
2. Enter BIOS Setup and load the default settings.
3. Hard disk drive cable.
4. Replace the hard disk drive.
5. Try another main board to make sure that the main board is
good.
Hard disk drive cannot format completely.
1. Enter BIOS Setup and load the default settings.
2. Hard disk drive cable.
3. Hard disk drive.
4. Try another main board to make sure that the main board is
good.
Hard disk drive has a write error.
1. Enter BIOS Setup and load the default settings.
2. Execute the utility program (with surface scan function, e.g., DOS
SCANDISK) to locate and block the usage of bad sectors.
3.
Reformat the hard disk drive.
4. Replace the hard disk drive.
Hard disk drive LED fails to light, but system operates
normally.
1. With the system power on, measure the voltage of the hard
disk LED connector.
2. Hard drive LED cable.
CD/DVD-ROM Drive
NOTE: Ensure that the CD/DVD-ROM drive is configured correctly in BIOS Setup, that the cables/jumpers are set
correctly, and that its laser beam is clean before diagnosing any CD/DVD-ROM drive problems.
CD/DVD-ROM drive test failed.
1. Check the CD/DVD-ROM drive cables.
2. Check the CD/DVD-ROM drive settings in BIOS Setup.
3. Replace CD-ROM/ DVD-ROM Drive.
CD/DVD-ROM drive LED doesn't come on but works
normally.
1.
CD/DVD-ROM
LED cable.
2. CD/DVD-ROM drive
CD/DVD-ROM drive LED flashes for more than 30
seconds before shutting off.
Software requests to reinstall the disc.
Software informs a reading CD/DVD disc error.
1.
The CD/DVD-ROM disc
may have dirt or foreign material on it.
Check with a known good disc.
2. The CD/DVD-ROM disc may not be inserted properly.
3. The CD/DVD-ROM disc is damaged.
CD/DVD-ROM drive cannot load or eject when the
system is turned on and its eject button is pressed and
held.
1. Disconnect all cables from CD/DVD-ROM drive except the
power cable and then press the eject button to try to unload
the disk.
2. CD/DVD-ROM drive power.
3. CD/DVD-ROM drive.
CD/DVD-ROM drive does not read and there are no
messages displayed.
1.
The CD/DVD-ROM disk
may have dirt or foreign material on it.
Check with a known good disc.
2. Ensure that the CD/DVD-ROM driver is installed properly.
3. CD/DVD-ROM drive.
CD/DVD-ROM drive can play an audio CD but there is
no sound output.
1. Ensure that the headphone jack of the CD/DVD-ROM has
output.
2. Turn up the sound volume.
3. Check the speaker power, connections and cables.
4. CD/DVD-ROM drive.
Real-time clock
Real-time clock is inaccurate.
1. Ensure that the information in the
Date and Time
of
BIOS Setup is set correctly.
2. RTC battery.
3. Main board.
Audio
Audio software program invokes but no sound comes
from the speakers.
1. Check the speaker power, connections and cables.
2. Turn up the sound volume.
Error Symptom
Action/FRU
Summary of Contents for Veriton 3000
