Acer EL1300 User Manual Download Page 56

Page: 56 / 80

Chapter 3: Troubleshooting

3 Right-click the name of the printer

you want to use. If the menu shows

a check mark next to Use Printer

Offline, click Use Printer Offline to

clear the check mark.

•

Wait until files have been printed before

sending additional files to the printer.

•

If you print large files or many files at one

time, you may want to add additional

memory to the printer. See the printer

documentation for instructions for

adding additional memory.

You see a “Printer is out of paper” error

message
After adding paper, make sure that the printer

is online. Most printers have an online/offline

button that you need to press after adding

paper.

Sound

You are not getting sound from the speakers

•

Make sure that the speakers are turned

on.

•

Make sure that the volume controls are

turned up.

•

Make sure that mute controls are turned

off.

•

If you are using external speakers, see the

speaker setup poster to check your

speaker connections.

•

Make sure that the universal jacks are

configured correctly.

Help

For more information about printer troubleshooting, click

Start

, then click

Help and Support

. Type

printer troubleshooter

in the

box, then press

NTER

Help

For more information about sound troubleshooting, click

Start

then click

Help and Support

. Type

sound troubleshooter

in the

box,

then press

NTER

Summary of Contents for EL1300

















































































Search results

Summary of Contents for EL1300

Reviews:

Brands by name

Popular brands

Acer EL1300, User Manual

Search results

Summary of Contents for EL1300

Reviews:

Brands by name

Popular brands