Acer Business B7 User Manual Download Page 20

Page: 20 / 36

EN-10

INSTALLATION

To install the monitor to your host system, please follow the steps as given
below:
Steps
1. 1-1 Connect Video Cable

a. Make sure both the monitor and computer are powered-OFF.
b. Connect the VGA cable to the computer.

1-2 Connect HDMI Cable (Only HDMI-input model)

a. Make sure both the monitor and computer are powered-OFF.
b. Connect the HDMI cable to the computer.

1-3 Connect DP Cable (Only DP-input model) (Optional)

a. Make sure both the monitor and computer are powered-OFF.
b. Connect the DP cable to the computer.

2. Connect the Audio Cable (Optional)
3. Insert the monitor power cable into the power port at the back of the

monitor.

4. Plug the power cords of your computer and your monitor into a nearby

electrical outlet.

5. Select Power-off USB charge ON/OFF to enable/disable Power-off USB

charge function. (Optional)

Note: Adjustment of the volume control as well as the equalizer to
other settings than the center position may increase the ear-/
headphones output voltage and therefore the sound pressure level.

HDMI

VGA

POWER

AC SWITCH

AUDIO IN

VGA IN

HDMI

optional

Summary of Contents for Business B7





































Search results

Summary of Contents for Business B7

Reviews:

Related manuals for Business B7

Brands by name

Popular brands

Acer Business B7, User Manual

Search results

Summary of Contents for Business B7

Reviews:

Related manuals for Business B7

Brands by name

Popular brands