background image

Special notes on LCD monitors ................................................................. 1
Introduction ................................................................................................ 2
Features ..................................................................................................... 2
Unpacking .................................................................................................. 3
Attaching/Removing the base .................................................................... 4
Screen position adjustment ......................................................................... 4
Connecting the power cord ........................................................................ 5
Safety precaution ....................................................................................... 5
Cleaning your monitor ................................................................................ 5
Preset  modes ............................................................................................. 6
Power saving ............................................................................................. 7
DDC .......................................................................................................... 7
Installation .................................................................................................. 8
User controls .............................................................................................. 9
Troubleshooting .........................................................................................13
Specification ..............................................................................................15

TABLE OF CONTENTS

For more information and help in recycling, please visit the following websites:

Worldwide:  http://global.acer.com/about/sustainability.htm

Summary of Contents for AL1716W


















Reviews: