background image

 

 

 

7.

 

There is a cover attached to the bottom of the 
backrest to cover the backrest hinge.  To fit this 
cover, place the first part of the cover (Fig 5, Item 
1) over the rear part of the hinge protection plate 
(Fig 5, Item 2), then pull the front part of the cover 
(Fig 5, Item 3) down over the hinge. 

 

8.

 

Figure 6 shows the backrest hinge cover from the 
inside.  Place the lower pocket of the backrest 
hinge cover (Fig 6, Item 1) over the lower part of 
the hinge protection plate (Fig 5, Item 4) to secure 
the hinge cover in place. 

9.

 

Repeat steps 7 and 8 to secure the cover on the 
other side. 

10.

 

Secure the backrest cushions to the backrest with 
the Velcro flaps.  Each cushion is attached to the 
backrest with the Velcro flap at the top of the 
cushion.  The top cushion has a double width 
Velcro flap and is marked Pillow 

 Top. The middle 

and bottom cushions are identical.   

11.

 

Ensure the female poppers on the overlay are 
engaged on the male poppers on the frame, 3 EA 
on left- and right-hand side. (Fig 7, Item 1) 

12.

 

To fit the sidepieces, pull out the plunger located 
under the seat on one side of the chair (Fig 8, Item 
1) and rotate it through 90 degrees to lock it open.  
Fig 9 shows the plunger locked open. 

13.

 

Undo the hand screw (Fig 8, Item 2). 

 

 

Figure 7 

 

Figure 4 

Figure 5 

 (Seat cushion shown removed for clarity.) 

Figure 6 

Figure 8 

1

1

Summary of Contents for CHAIR-0-SC1-030

























Reviews: