background image

7

www.acclaimlighting.com

FITTING A SPREAD LENS

The standard beam angle is 6 degrees. This can be adjusted by inserting an appropriate 
spread lens into the inside of the front panel.   

TO FIT A SPREAD LENS

Notes: This operation is best achieved with the Dyna Accent front face lying horizontally. Install 
spread lenses only in dry conditions to avoid any build up of condensation.

1  Using a 3mm Allen wrench (hex key), slightly loosen each of the four bolts that secure the 

front hood to the main body of the fixture. Once all bolts have been suitably loosened, 
remove all four of them plus their small washers and lift off the front hood.

2  Remove the protective films from both sides of the spread lens.
3  Ensure that the black rubber gasket is correctly in place around the circumference of the 

spread lens. Find the 

Locating tab

 on one side of the rubber gasket and ensure that this 

tab faces towards the front face of the Dyna Accent - and aligns with 

Locating notch

 in the 

front face. 

4  Place the front hood over the spread lens and Dyna Accent front face, ensuring that the 

Drain hole

 of the front hood aligns with the drainage 

Recess

 in the rubber gasket of the lens.

5  Reintroduce the four bolts and their washers, and tighten sufficiently.          

Spread lens

Front hood

Locating notch

Locating tab

Drain 

hole

Recess

Summary of Contents for Dyna Accent

























Reviews: