AccessPRO INDUSTRIAL XB220H06K, Technical Instructions

Page: 1 / 13

XB220H06K
TECHNICAL INSTRUCTIONS
WARNINGS FOR THE INSTALLER – GENERAL SAFETY OBLIGATIONS
1
ATTENTION! It is very important for the safety of people to follow all instruc-
tions strictly. A wrong installation or use of the product could cause serious
damage to people. 17
‚ª‚éåËÂ子­ÄÞ傽½‚å­ËÄÞªË齖ª‚ôš‚彚‚ÞåËĚ½­¥ªå­Ä¥–šô­šĸ­Īšģą‚Þª­Ä¥½­¥ªåÞ
integrated in the crosshead of the bollard) and a signal placard, along with the device
quoted at point “16” 2 Read carefully this manual before starting installation and save it
for future reference. 18 In each automatic installation the installer must consider.
2
Read carefully this manual before starting installation and save it for future
reference.
18
In each automatic installation the installer must consider and install appropriate safety
devices.
3
Packaging materials (i.e. plastic, polystyrene, etc.) must be out of children’s
reach, because potentially dangerous.
19 For maintenance works use only original parts supplied by AccessPRO INDUSTRIAL.
4
This product has been designed and manufactured exclusively on the purpose
indicated in this manual. Any different use not here indicated could damage the
integrity of the product and/or be potentially dangerous.
20
AccessPRO INDUSTRIAL is not responsible for safety and good functioning of the
product , in case of use of components not manufactured or distributed by AccessPRO
INDUSTRIAL.
5
AccessPRO INDUSTRIAL is not responsible for any damage caused by impro-
per or different use from the indicated one.
21
ËÄËå‚××½û‚ÄûÃ˖­Ą‚å­ËÄåË媚ׂÚåސËÃ×Ëޭĥ媚‚éåËÂ嚖×Ú˖éåšÞÞ
-
PRO INDUSTRIAL.
6
ËÄËå­ÄÞ傽½åªš–šô­š­Ä‚Äšú×½ËÞ­ôš‚Úš‚ģgÞ­Ä¥/Äą‚Ͻš¥‚ޚސË齖
be not safe.
22
The installer must provide the Customer with all information related to the manual relea-
se of the automatic bollard in case of emergency and give the User a warning manual
attached to the product.
7 Installation must be according to the local Laws. 23 Do not allow children or others to stop close to the bollard during operation.
8
In order to have an adequate safety level in the extra-CEE
countries, in addiction to the national laws, the above mentioned laws must be
followed.
24
Keep remote controls or other impulse-giving devices out of children’s reach, in order to
avoid involuntary activation.
9
AccessPRO INDUSTRIAL is not responsible if someone does not observes the
correct method of installation of the AccessPRO INDUSTRIAL products and
related devices, included deformations coming during the use.
25
Thoroughfare over the AccessPRO INDUSTRIAL bollard allowed only at complete
lowering of the bollard.
10 Before any actions on the automatic installations take power off. 26
Semiautomatic bollards are not adviceable for multiple installation (two or more) on
main streets where the frequent passage of vehicles over the lowered bollards can
break the lock block and make the bollard lifting without control.
11
An Omni polar switch should be foreseen on the alimentation’ s net of automatic
installations. Its connections should have an opening range of 3 mm. A magne-
totermical differential with 6A Omni polar switch is adviceable
27
The User must avoid any repairing actions or direct operations on the bollard, and must
‚––ÚšÞÞåËÙ邽­Ąš–‚Ä–‚éåªËÚ­Āš–ךÚÞËÄĚ½ËĽûĪ
12
Assure that a differential switch with 0,03° is present at the
beginning of the automatic installation.
28
Do not waste exhausted batteries in the garbage, but dispose them in the apposite con-
tainers to allow recycling. Disposal costs have already been paid by the manufacturer.
13
The main electrical alimentation of the control unit of automatic installations
must be connected directly to at the beginning of the apposite principal switch
ޚå­ÄÞ­–šåªšËÄåÚ˽éÄ­åįéޚ‚Äå­Ľą‚ڐ‚½šÞ‚××ÚËôš–û‚彚‚ÞåËĚˤ
媚éÚËך‚Ä/ÄÞå­åéåšÞĪcªš–­ÃšÄÞ­ËÄˤ媚ĄÚÞ傽­ÃšÄå‚å­ËĽ­ÄšÃéÞ叚
minimum 3x2,5mm,but evaluated by the installer according to the number of
AccessPRO INDUSTRIAL bollards (400W each AccessPRO INDUSTRIAL
bollard) and the distance from the output point in order to guarantee a correct
alimentation (230V +/- 10% for moving AccessPRO INDUSTRIAL bollard).
29
The product is packaged on Euro pallet; use pallets’ movers or shunters for movement;
handle
with care.
14 Test that the earthing is workmanlike and connect the metallic parts. 30
The product has been manufactured with IP 56 protection’s level, and could therefore
be stored everywhere; storage in internal or covered places is anyway preferable.
15
The automatic installations include a standard safety device: an inversion
pressure switch in case of at least 40 kg of load. It is anyway necessary to test
the activation level every six months, according to what laws establish.
31
The product does not require availability of spare parts; AccessPRO INDUSTRIAL’s
warehouse can send by express any needed spare parts.
16
Safety devices (Law EN 12978) allow protection of potentially dangerous areas
where activities such as squashing, conveyance, shearing are possible to
occur.
32
In case of maintenance and/or reparation, Pay attention not to give improper raising
signals; to avoid any problems, disconnect the bollard’s moving by the switch set inside
the control management station.
33 Everything not mentioned in this manual is not allowed.