background image

1

Thank you for purchasing ACCESS

®  

LORADO

®

 Roll-Up Cover. ACI

®

 

manufactured this cover with pride using superior quality materials and 

workmanship. With proper care, your cover will provide years of service and 

enjoyment.

NOTICE TO INSTALLER: 

It is recommended instructions are read before 

installation, even if familiar with cover. Improvements may be made without 

prior notice. Always handle cover and components with care. If you have any 

problems or questions, have serial number ready and call customer service. 

When done, this owner’s manual must be given to the consumer.

NOTICE TO CONSUMER:

 Before using cover, read operating, maintenance, 

and safety sections and save owner’s manual for future reference.

Tested. Trusted. Guaranteed.

FOR YOUR RECORDS

DATE PURCHASED:

WHERE PURCHASED:

SERIAL NUMBER:

Customer Service Hours: 

8:00am-5:00pm CST, Mon. - Fri.

Problems? Questions? Missing or 

Damaged Parts? Install Questions?

Call Us First!

1-866-630-8726

(Located on decal under rear bar by tailgate)

INSTALLATION INSTRUCTIONS 

AND OWNER’S MANUAL

HELP LINE

HELP LINE

STOP

Summary of Contents for LORADO













Reviews: