1
(4) PREPARE THE FIXTURE
1. If you are replacing an existing fixture, disconnect and remove
the old fixture. Expose the supply wiring from the outlet box.
2. Lay the un-assembled fixture on a soft surface and carefully
remove all the packing material.
3. Using the fixture back plate determine positioning to drill holes
on wall, relative to J-box, to provide additional support to fixture.
Four
(5) Screw plugs
are provided.
4.
Option1:
Attach the supplied
Crossbar
to the
J- box,
with the
supplied
(4)
Mounting Screws
. Then install the
Mounting
Plate
, with the supplied
(6) Washer and Nut
are provided. Use
Four
(7) Screws
to secure the Mounting Plate to the ceiling.
Option2:
Attach the supplied
Mounting Plate
to the
J- box,
with the supplied
(4)
Mounting Screws
. Use Four
(7) Screws
to
secure the Mounting Plate to the ceiling.
5. Pull the supply wires through the Center Hole in the Crossbar.
6. Connect the
BLACK supply wire
to the
Black wire
of the
fixture with supplied
(8) Wire nuts
ensuring a secure
connection.
7. Connect the
WHITE supply wire
to the
White wire
of the fixture
with supplied
(8) Wire nuts
ensuring a secure connection.
8. Attach the
Green/Ground wire
from the fixture to the
Electrical
Supply Wire
or to the
Green Screw
located on the
Universal
Crossbar.
Secure these connections with supplied
Wire
Connectors
and tape these connections with U.L Listed
electrical tape(not supplied). Tuck all of the wires carefully into
the J-Box.
9. Put the crossbar screws through the 4 holes allocated on the
(9) Canopy
. Secure the fixture against the ceiling with the
supplied
(9) nuts.
10. Insert the
(10) Tube
.
DO NOT EXCEED THE WATTAGE AS
INDICATED ON THE WARNING LABEL.
11. Holding the
(11) Top glass with thumb screws.
12. Restore electricity and enjoy your new lighting fixture.
CAUTION:
Ensure that the Fitting is Cool and Switched off, Before
Changing Bulbs.
Do Not use Bulbs Exceeding Maximum Wattage, As Per
Caution Label.
Do Not Touch the Bulb while fixture is in operation.
Warning-Risk of fire and electric shock.
Important safety instructions.
Do not install this fixture in hazardous locations.
***READ & SAVE THESE INSTRUCTIONS ***
ACCESS LIGHTING
MODEL # 31027 / 31028 / 31029 / 31030
INSTALLATION & OPERATION INSTRUCTIONS
1
) TOOLS AND MATERIALS REQUIRED
Blade Screwdriver
Star Screwdriver
Wire Cutters
Wiring supplies as required by Electrical Code
Attention:
Before assembling your lighting fixture, please
read the following instructions.
(2) GENERAL
1.
To ensure the success of the installation, be sure to read these
instructions thoroughly before beginning.
2.
All electrical connections must be in accordance with local
codes, ordinances, or the National Electrical Code. If you are
unfamiliar with methods of installing electrical wiring, secure the
services of a qualified licensed electrician.
3.
These fixtures are intended for mounting to a standard 4” x 2 ¼”
deep metal octagon outlet box. The box must be directly
supported by the building structure.
4.
Before commencing with the installation,
disconnect the power
by turning off the circuit breaker
or by removing the fuse at
the fuse box. Turning the power off using the light switch is not
sufficient to prevent electrical shock.
NOTE:
The important safeguards and instructions appearing in
this manual are not meant to cover all possible
conditions and situations that may occur. It must be
understood that common sense, caution and care, are
factors that cannot be built into any product. The
person(s) caring for and operating the fixture must
supply these factors
.
(3) UNPACKING THE FIXTURE
On checking the contents of the box you will find;
1.
Fixture assembly
2.
Mounting Hardware Packet
3.
Crossbar
4.
1 x Top Glass
5.
1x 24W T5 HO Linear Fluorescent Tube , 2x24W or 1x39W
or 2x39W (Model Dependant)
Do not install this fixture assembly closer than 6 inches
from any curtain or similar combustible material.
a c c e s s
L I G H T I N G
