background image

Assembly Instructions / Turbochargers A131-R, A136-R

1 Introduction / 1.4 Definition of warning, caution, note

© Copyright 2023 Turbo Systems Switzerland Ltd. All rights reserved.

HZTL455311P0044_EN

Rev. A

April 2023

Accelleron

Accelleron Industries Ltd is referred to in this document as Accelleron.

Official Accelleron service stations

Accelleron service stations are regularly audited and certified by Accelleron Industries Ltd (see "Con-
tact Information" on the website 

www.accelleron-industries.com

).

1.4

Definition of warning, caution, note

 WARNING

Definition of Warning

Non-compliance or inaccurate compliance with working or operating instructions in-
dicated by this symbol and the word WARNING can lead to serious injuries to per-
sonnel and even to fatal accidents.

u

Warning signs must always be observed.

 CAUTION

Definition of Caution

Non-compliance or inaccurate compliance with working or operating instructions in-
dicated by this symbol and the word CAUTION can lead to serious damage to en-
gine or property with grave consequences.

u

Caution signs must always be observed.

NOTICE

Note

The note provides advice which facilitates the work.

Page 

3

 / 

17

Summary of Contents for Turbocharger A131-R





















Reviews: