background image

1

INSTRUCTIONS FOR FINAL ASSEMBLY

The Wattage Thermalaire EP ARF is distributed exclusively by Global Hobby Distributors

18480 Bandilier Circle, Fountain Valley, CA  92728

All contents copyright © 2000, Global Hobby Distributors  Version V1.0  8/00

Wattage guarantees this kit to be free from defects in both material and workmanship, at the date of purchase.  This
does not cover any component parts damaged by use, misuse or modification.  In no case shall Wattage's liability
exceed the original cost of the purchased kit.

In that Wattage has no control over the final assembly or material used for final assembly, no liability shall be
assumed for any damage resulting from the use by the user of the final user-assembled product.  By the act of using
the final user-assembled product, the user accepts all resulting liability.

To make your modeling experience totally enjoyable, we recommend that you get experienced, knowledgable help with
assembly and during your first flights.  Your local hobby shop has information about flying clubs in your area whose
membership includes qualified instructors.  We also recommend that you contact the AMA at the address below.  They
will be able to help you locate a flying field in your area also.

Academy of Model Aeronautics

5151 East Memorial Drive

Muncie, IN 47302-9252

(800) 435-9262

www.modelaircraft.org

Summary of Contents for Wattage Thermalaire EP





























Reviews: