Abus SHBW10000 Manual Download Page 2

 

English 

 

Introduction 

 

Dear customer, 

We are pleased that you have chosen our product and thank you for your trust! You made a good 
choice. 

This 4in1 Sensor (hereinafter referred to as the "device") has been developed and manufactured with 
the utmost care. Please read these operating instructions completely and observe all operating and 
safety instructions, as this ensures the best possible handling of the device. This document is an 
installation and maintenance manual. 

 

If you have any questions, please contact your specialist trade partner  

or contact our customer service: 

 

Mail: ABUS Support, Linker Kreuthweg 5, 86444 Affing, Germany 

E-mail: [email protected] 

Phone: +49 8207 959 90 888 

Hotline opening hours: Mon-Thu: 08 - 17 h; Fri: 08 - 14 h 

 
 
 

ABUS Security-Center hereby declares that the enclosed product comply with the requirements 
of the following directives 

RED Directive (2014/53/EU), EMC Directive (2014/30/EU), Low Voltage Directive (2014/35/EU) and 
RoHS Directive (2011/65/EU). The full EU Declaration of Conformity text can be found at:  

www.abus.com/product/SHBW10000

 

It can also be obtained at the following adress: 

ABUS Security-Center GmbH & Co. KG, 

Linker Kreuthweg 5, 86444 Affing, GERMANY 

 

 

 

 

 

All contained company names and product designations are trademarks of the respective owners. All 
rights reserved. 

 

 

Disclaimer of Liability 

These operating instructions have been prepared with the greatest care. Should you nevertheless 
notice omissions or inaccuracies, please inform us in writing at the above address. 

Your rights are limited to the repair or replacement of this product as delivered. ABUS Security Center 
assumes no liability for any special, incidental or consequential damages, including but not limited to 
loss of revenue, loss of profit, restrictions in the use of the software, loss or recovery of data, costs 
for replacement equipment, downtime, property damage and claims of third parties, as a result of and 
in connection with the use of the software.a. warranty, contractual, legal or claims for damages 
notwithstanding other limited or implied warranty provisions or in the event that the limited warranty 
does not apply, the scope of liability of ABUS Security Center is limited to the purchase price of the 
product. 

The contents of this manual are subject to change without notice. 

© ABUS Security-Center GmbH & Co. KG, 09/2018 

Summary of Contents for SHBW10000
















Reviews: