manualshive.com logo in svg

ABL eMH3, Installation Manual

Share
Download
ABL eMH3 Installation Manual Download Page 43

Charging procedure  –   

Manual RFID card administration     |

43

Charging procedure

After installation and configuration, the eMH3 is ready for operation immediately, and can now be used to charge an 

electric vehicle.
Please follow these steps to charge your vehicle using the Wallbox eMH3:

1 

Park your electric vehicle so that its charging inlet can be easily reached with the charging cable's charging con-

nector.

2 

Check the LED indicators of the wallbox (illustra-

tion: 1 cycle).

 

y

When the charge point is ready for charging 

operations, the blue LED flashes while the green 

and red LEDs are OFF.

3 

Prepare the charging cable of the wallbox and the 

vehicle's charging inlet.

 

y

Wallbox with charging cable  

Slightly lift up the charging connector and pull it 

downwards from its storage compartment. Open 

the charging inlet at the vehicle and plug in the 

charging connector.

 

y

Wallbox with charging socket 

 

Open the charging inlet at the vehicle and plug in 

the charging connector. Then open the charging 

socket lid on the wallbox and plug in the charg-

ing connector.

4 

Check the LED indicators of the wallbox (illustra-

tion: 1 cycle).

 

y

If the vehicle is connected and the wallbox 

is waiting for authorisation of the charging 

procedure, the blue LED of the charge point is 

continuously ON.

NOTE

Authorisation via RFID

The RFID module is located in the upper part of the housing cover, which, depending on the model variant and 

configuration of the Wallbox eMH3, is used for the authorisation of the charging procedure by the user.

 

ƒ

Controller with or without Extender: 

To authorise charging procedures via RFID, the Wallbox eMH3 must 

be operated with a backend. This operating state is indicated by the flashing green LED of the RFID module.

 

ƒ

Extender without Controller:

 If an Extender wallbox has been configured for operation without a Controller, 

you must authorise the charging procedure via RFID if the blue LED of the RFID module is flashing twice per 

cycle.  

If the blue LED is only flashing once per cycle, the RFID module is inactive and the charging procedure will 

start automatically upon being requested by the vehicle: Steps 

5

 to 

8

 as described below do not apply in this 

case.

Summary of Contents for eMH3



































































Reviews:

No comments

Brands by name

Popular brands

Load more brands