ABL eMH3 Installation Manual Download

Page: 11 / 66

Introduction to the Wallbox eMH3 –

Accessories |

Bundled variants of the eMH3 also include:

reev onboarding letter, 1 pc

(Controller/Con only)

reev RFID card, 2 pcs

QR code stickers, 1 or 2 pcs

(depending on number of charge

points)

Controllers only:

LTE USB stick with

SIM card (preconfigured), 1 pc

LTE

NOTE

Checking the components included

Check immediately after unpacking whether all components are included: should any components be missing,

please contact the dealer from whom you purchased the wallbox.

Accessories

The following accessories for the Wallbox eMH3 are available separately:

CONFCAB

Configuration kit for connecting all ABL charging stations to a Windows PC for

configuration via specific software applications by ABL

LASTMZ1

External energy meter for connection to a Controller charging station or exter-

nal control unit

LASTMZ2

Coil sensors for connection to the energy meter LASTMZ1

E017869

For all eMH3 model variants, except bundle products: Set of ID tag cards (5 pcs)

to extend user pool

LAK32A3

Type 2 charging cable according to IEC 62196-2, up to 32 A 240/415 V AC,

3-phase, length ca. 4 m

LAKC222

Type 2 charging cable according to IEC 62196-2, up to 20 A 240/415 V AC,

3-phase, length ca. 7 m

LAKK2K1

Type 2 to Type 1 adapter cable according to IEC 62196-2, up to 32 A 230 V AC,

single phase, length ca. 4 m

Summary of Contents for eMH3



































































Search results

Summary of Contents for eMH3

Reviews:

Related manuals for eMH3

Brands by name

Popular brands

ABL eMH3, Installation Manual

Search results

Summary of Contents for eMH3

Reviews:

Related manuals for eMH3

Brands by name

Popular brands