background image

|     Configuring the Wallbox eM4 Twin  

44

Control Board settings and reboarding

To complete the configuration of the selected operating mode, you can switch to the 

Control Board

 of the 

ABL 

Configuration App

 on the last screen. Here you can check all the settings you have made so far and change them if 

necessary, as well as set up further parameters for operation.
Using the 

reboarding

 process, you can also open the 

Control Board

 at a later date to adjust all settings of the 

wallbox(es).

 

ƒ

If you use the same device as during the initial setup, you can open the 

Control Board

 without entering your 

login credentials.

 

ƒ

If you are using a new device or have reinstalled the app, you must re-enter your login credentials to open the 

Control Board

. Alternatively, you can scan the QR code generated at the end of each onboarding process to log 

in.

The following parameters can be adjusted in the 

Control Board

, regardless of the selected operating mode.

Parameter

Description

Start/stop charging

Start or stop the charging process for a charge point, provided a vehicle is 
connected.

Lock charging cable

Permanently lock the connected charging cable in the charging socket of the 
wallbox and unlock it again at a later date.

Monitoring

Allows you to access various information such as charging current, charging 
status, readiness for operation, etc., as well as faults.

Software update

Allows you to install new software on the wallbox as soon as it is available.

Network settings

Adjust the network settings for communication via WLAN and/or LAN or set 
them to offline.

RFID management

Remove RFID media that have already been configured and add new media for 
authorisation.

Diagnosis

View information on faults and malfunctions during operation.

Change language

Switch the user language of the app between 

DE

 and 

EN

 after the initial 

setup.

Send configuration report

Allows you to generate a report of all current settings (charging currents, RFID 
UIDs, phase imbalance, etc.) and then send it by email.

Only in 

Controller / Extender

 mode:

Add additional extenders

Register additional Extender charging stations with the Controller. Please note, 
however, that the maximum limit of 30 charge points that can be managed via 
a single Controller still applies.

Summary of Contents for eM4 Twin







































































Reviews: