manualshive.com logo in svg

ABB XIO-00, User Manual

Share
Download
ABB XIO-00 User Manual Download Page 194

194

 | XIO USER MANUAL | 2106424MNAB 

 

 

Figure 9-11: XIO 4 Network support (2 Enterprise and 2 Industrial Networks) 

 

 

 

 

 

 

 

 

 

IMPORTANT NOTE: 

After completing the configuration of each Enterprise interface, both A1 and 

A2 should display as options in the Enterprise Interface drop-down list in the XIO’s Port 

Forwarding tab. If the XIO will be used in port forwarding mode, define port forwarding rules. 

See section 

9.7.7 Define port forwarding rules

. 

 

 

 

 

 

 

IMPORTANT NOTE: 

After completing the configuration of the Industrial interfaces, the enabled 

interfaces (B1 and B2) should display as options in the Enterprise Interface drop-down list in the 

Port Forwarding tab. If the XIO will be used in port forwarding mode, define port forwarding 

rules. See section 

9.7.7 Define port forwarding rules

. 

9.7

 

Port forwarding 

The XIO 3- or 4-network support provides options to separate connected Totalflow devices into different 

logical networks. In addition to this capability, the XIO also supports port forwarding. When an XIO is in 

port forwarding mode, it can be used as a gateway with specific rules to control access to other field 

devices. For example, the XIO can be connected to the corporate network on one of its Ethernet interfaces 

 

Summary of Contents for XIO-00
















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands