ABB XIO-00 User Manual Download Page 177

Page: 177 / 207

XIO USER MANUAL | 2106424MNAB |

177

8.6.2

Reconnect power to the device

Follow this procedure to reconnect the power port terminal connectors or the power cables back into the

XIO. You do not need to rewire if the connectors are not removed from the cables. This procedure

assumes wiring was left intact before terminal connector removal.

NOTICE – Equipment damage.

Do not reconnect the external power until all service

procedures are complete. This includes reconnecting all wires, plugs, terminations, and

peripheral equipment. Otherwise, property damage can result. Do not perform this procedure

until you receive instructions to do so.

8.6.3

Remove the XIO from the DIN rail

To remove the XIO from the DIN rail:

Figure 8-36: Remove XIO from DIN rail

Legend: Remove XIO from DIN rail

Description

DIN rail clip

Summary of Contents for XIO-00
















































































































































































































Search results

Summary of Contents for XIO-00

Reviews:

Brands by name

Popular brands

ABB XIO-00, User Manual

Search results

Summary of Contents for XIO-00

Reviews:

Brands by name

Popular brands