ABB XAC24061 Operation Manual Download Page 79

Page: 79 / 140

Operation Manual / 4 Product description / A100-L

7 Troubleshooting / 7.3 Surging of the turbocharger

HZTL4034_EN

Rev.R

October 2020

Charge air pressure too high

Engine performance and engine speed unchanged, suction condition normal

Possible causes

Remedy

Turbochar-
ger

Manometer display not correct

Replace manometer

Engine

Malfunction in the injection system

Repair or contact manufacturer

Injection mistimed

Set correctly

Engine performance higher than indic-
ated

Check engine performance

Table 22: Malfunctions during operation – Charge air pressure too high

7.3

Surging of the turbocharger

Possible causes

Remedy

Turbocharger

Filter silencer or diffuser contamin-
ated

Clean (

Periodic maintenance

→

)

Heavy dirt deposits in the turbine or
in the nozzle ring

Engine

Protective grating in front of the tur-
bocharger contaminated or damaged

Clean/replace

Charge air
cooler

Cooler contaminated

Clean

Charge air duct blocked

Table 23: Surging of the turbocharger

CAUTION

Continuous or periodic surging

If the turbocharger surges continuously or periodically, parts of the tur-
bocharger may be damaged.

Gradually reduce the engine load.

Have the cause clarified and remedied immediately by an ABB Turbochar-
ging Service Station.

Have parts assessed for damage and, if necessary, replaced by an ABB
Turbocharging Service Station.

Page

110

Summary of Contents for XAC24061












































































































































Search results

Summary of Contents for XAC24061

Reviews:

Related manuals for XAC24061

Brands by name

Popular brands

ABB XAC24061, Operation Manual

Search results

Summary of Contents for XAC24061

Reviews:

Related manuals for XAC24061

Brands by name

Popular brands