ABB TPS48-H33 Operation Manual Download | Manualshive

Page: 43 / 130

background image

Operation Manual / 4 Product description / TPS44-H.. - TPS52-H..

2

Removing and Installing

Page 13 / 99

© Copyright 2016 ABB. All rights reserved.

HZTL4037_EN

Revision A

August 2016

Figure 5: Removing the turbocharger

1.  Treat the threads of studs and nuts with penetrating oil and allow to work in.
2.  Loosen and remove nuts.
3.  If present: Disconnect the plug to the speed sensor (86505) and secure the rolled-up cable

on the turbocharger. This protects the plug from being crushed.

4.  Install the swivel lifting eye (S) and attach the lifting gear to it.
5.  Lift the turbocharger away from the support vertically.
6.  Cover the connections.

Version with water cooling

CAUTION

Freezing of the cooling water in the bearing casing
If cooling water freezes in the bearing casing, this can lead to severe dam-

age.



For transport and storage of the turbocharger, drain the cooling water

from the bearing casing via one of the two bottom openings of the water

connections.

«
...
41
42
43
44
45
...
»

Summary of Contents for TPS48-H33



































































































































Reviews:

No comments

Related manuals for TPS48-H33

Brand: GE Pages: 24

Brand: ICS ELECTRONICS Pages: 6

Brand: HAMAR LASER Pages: 49

Brand: DBX Bushido Pages: 12

Brand: Garmin Pages: 10

Brand: Garmin Pages: 26

Brand: Naviom Pages: 31

Brand: HABYS Pages: 16

Brand: Tactile Medical Pages: 23

Brand: Taarup Pages: 72

Brand: Tar River Pages: 44

Brand: Tar River Pages: 61

Brand: Zell Pages: 32

Brand: Uflex Pages: 16

Air 2000 Outdoor

Brand: ubbink Pages: 21

MCX-C15 - MusicCAST Network Audio Player

Brand: Yamaha Pages: 65

Brand: Yamaha Pages: 24

Brand: Varimixer Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands