ABB TPL65VA32 Operation Manual Download

Page: 99 / 124

Operation Manual / TPL65VA32/33

Disassembly and assembly

Removing variable turbine geometry

module with gas inlet casing

8.7

Page 97

ber

2016

ZTL

2464_

ion

Removing variable turbine geometry module

with gas inlet casing

8.7



Disconnect semi-circular section of sealing air line (A) from variable

turbine geometry module.



Retaining clips (56121) are fitted.



Unscrew nuts (61042).



Remove gas inlet casing (51001) together with variable turbine geom-

etry module (56100).

CAUTION

After removing screws (56122) and retaining clips (56121), gas inlet

casing (51001) is no longer secured.



Loosen screws (56122) together with retaining clips (56121) and re-

move with clamping ring (56112).



Remove clamping ring (56112).



Carefully separate gas inlet casing (51001) from variable turbine ge-

ometry module (56100) and remove it.

CAUTION

Have the variable turbine geometry module overhauled by ABB Turbo

Systems. ABB Turbocharging Service Stations have variable turbine

geometry modules replaced with overhauled ones as part of the CPEX

(Customer Part Exchange) programme.

8.7

Summary of Contents for TPL65VA32





























































































































Search results

Summary of Contents for TPL65VA32

Reviews:

Related manuals for TPL65VA32

Brands by name

Popular brands

ABB TPL65VA32, Operation Manual

Search results

Summary of Contents for TPL65VA32

Reviews:

Related manuals for TPL65VA32

Brands by name

Popular brands