1SDH002031A1002 ECN000092998 Rev. B
SACE Tmax XT2
– XT4 | 60
OQ Protection
Function
If one or more reactive powers read by the unit exceeds the Q27 threshold for a time greater than
t27, the protection sends the TRIP command.
To verify and simulate the trip times based on all the parameters, see:
Protection summary table with the operating characteristics (page 79)
Chart with tripping curve (page 92)
Parameters
Parameter
Description
Default
Enable
Enables/disables protection and availability on menu of the
parameters
OFF
Trip Enable
Activates/deactivates the open command: if disabled, the alarm
and the lapsing of the protection time are managed only as
information
OFF
Threshold
Q27
Defines the value that activates the protection.
The value is expressed both as an absolute value (kVAR) and as a
relative value (Sn), settable in a range:
0.4 Sn .. 2 Sn with 0.001 Sn step
1 Sn
Time t27
This is the trip time of the protection; the value is expressed in
seconds, which are settable in a range:
0.5 s ..100 s, with 0.5 s step
1 s
Constraints, limitations, and additional functions
From the service connector (with Ekip Connect) or with system bus communication it is also
possible to access the block functions, see page70.
OP Protection
Function
If one or more active powers read by the unit exceeds the P26 threshold for a time greater than
t26, the protection sends the TRIP command.
To verify and simulate the trip times based on all the parameters, see:
Protection summary table with the operating characteristics (page 79)
Chart with tripping curve (page 92)
Parameters
Parameter
Description
Default
Enable
Enables/disables protection and availability on menu of the
parameters
OFF
Trip Enable
Activates/deactivates the open command: if disabled, the alarm
and the lapsing of the protection time are managed only as
information
OFF
Threshold
P26
Defines the value that activates the protection.
The value is expressed both as an absolute value (kW) and as a
relative value (Sn), settable in a range:
0.4 Sn .. 2 Sn with 0.001 Sn step
1 Un
Time t26
This is the trip time of the protection; the value is expressed in
seconds, which are settable in a range:
0.5 s ..100 s, with 0.5 s step
1 s
Constraints, limitations, and additional functions
From the service connector (with Ekip Connect) or with system bus communication it is also
possible to access the block functions, see page70.
Summary of Contents for SACE Tmax XT2
