manualshive.com logo in svg

ABB REU615, Applications Manual

Share
Download
ABB REU615 Applications Manual Download Page 71

Terminal

Description

X130-16

RTD5 (AI7), -

X130-17

RTD6 (AI8), +

X130-18

RTD6 (AI8), -

1) Common ground for RTD channels 1-3.

2) Common ground for RTD channels 4-6.

5.1.3 

Auxiliary supply voltage input

The auxiliary voltage of the IED is connected to terminals X100/1-2. At DC
supply, the positive lead is connected to terminal X100-1. The permitted auxiliary
voltage range (AC/DC or DC) is marked on the top of the LHMI of the IED.

Table 29:

Auxiliary voltage supply

Terminal

Description

X100-1

+ Input

X100-2

- Input

5.1.4 

Binary inputs

The binary inputs can be used, for example, to generate a blocking signal, to
unlatch output contacts, to trigger the disturbance recorder or for remote control of
IED settings.

Table 30:

Binary input terminals X110-1...13

Terminal

Description

X110-1

BI1, +

X110-2

BI1, -

X110-3

BI2, +

X110-4

BI2, -

X110-5

BI3, +

X110-6

BI3, -

X110-6

BI4, -

X110-7

BI4, +

X110-8

BI5, +

X110-9

BI5, -

X110-9

BI6, -

X110-10

BI6, +

X110-11

BI7, +

X110-12

BI7, -

X110-12

BI8, -

X110-13

BI8, +

1MRS757054 A

Section 5

IED physical connections

REU615

65

Application Manual

Summary of Contents for REU615

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands