ABB RELION 650 SERIES Engineering Manual Download Page 87

Page: 87 / 110

IEC08000418.vsd

IEC08000418 V1 EN-US

Figure 67: IEC 61850: Export IED file Options

7.4

Engineering of vertical and horizontal communication

in IET600

GUID-04ED1306-BAE6-49D2-8C84-11849EACC711 v7

For IEC 61850 engineering a separate system configuration tool is needed to be used with

PCM600. In PCM600 Ver. 2.3 or earlier the recommended tool is CCT600. In PCM600 Ver. 2.4 or

later the recommended tool is IET600, which is also included in the PCM600 Engineering Pro

installation package. In PCM600 Ver. 2.5, a lot of engineering described below can be done in

the PCM directly.

Procedure for signal engineering for the station by using IET600:

Create a project in IET600.

Import the SCD file exported from PCM600.

All data sets, report control blocks and GOOSE control blocks must be

located at LD0/LLN0. Due to IED capability, there are limitations regarding

the maximum number of data sets, number of entries in a data set and the

number of report control blocks that can be used.

Add and/or reconfigure default data sets. The 650 series configured IED includes a

number of predefined data sets, but it is possible to add additional data sets and/or

reconfigure default data sets according to the requirements.

Note that reporting data sets shall only contain data intended to be used

by clients, for example for event handling.

4. Configure report control blocks for each data set used for vertical communication. The

650 series configured IED includes a number of predefined report control blocks, but it is

possible to add additional control blocks and/or reconfigure default control blocks

according to the requirements.

Up to 8 report clients can be configured.

5. Connect the report control blocks to vertical IED clients. The report control blocks are

connected to the vertical clients in the SCD file for a 650 series pre-configured IED. Check

each IED client and configure them to the subnetwork before connecting report control

blocks to the clients.

6. Create a GOOSE message data set for the sending IED. Define the content of the data set

according to the requirements.

1MRK 511 284-UEN B

Section 7

IEC 61850 communication engineering

650 series

Engineering manual

Summary of Contents for RELION 650 SERIES













































































































Search results

Summary of Contents for RELION 650 SERIES

Reviews:

ABB RELION 650 SERIES, Engineering Manual, Page: 87 / 110

Search results

Summary of Contents for RELION 650 SERIES

Reviews: