ABB RELION 650 SERIES Engineering Manual Download Page 67

Page: 67 / 110

started when the first signal of the disturbance changes to ON. tMax is stopped, when tReset

could clear all LEDs.

A disturbance runs for a maximum of some seconds, while tReset can be in the range of 60 to

90 seconds.

The timer tReset and tMax are configured in Parameter Setting tool as part of the function

block LEDGEN

IEC08000401.vsd

= Steady

= Flash

Illumination =>

Man-

Reset

tMax

tRestart

S1LED

S2LED

S3LED

S4LED

Auto-

Reset

IEC08000401 V1 EN-US

Figure 53: LHMI LED operation mode LatchedReset-S / 2

6.2

Single-line diagram engineering

GUID-4EF97104-327A-443F-AA00-7C4BF143D46D v2

Phase angles are shown as radians in the single line diagram (GDE measurand)

symbols but in degrees in other views on the LHMI.

6.2.1

Concept description to present and generate diagrams in

graphical display editor

GUID-3C532F5A-3E26-4A3A-ACE3-C7758494BE4D v6

Additional concept information to use GDE, see

Figure 54

•

Different GDE windows

•

HMI display raster layouts

•

Drawing lines (doing a Link)

1MRK 511 284-UEN B

Section 6

Local HMI engineering

650 series

Engineering manual

Summary of Contents for RELION 650 SERIES













































































































Search results

Summary of Contents for RELION 650 SERIES

Reviews:

ABB RELION 650 SERIES, Engineering Manual, Page: 67 / 110

Search results

Summary of Contents for RELION 650 SERIES

Reviews: