ABB Relion 650 Series REL650 Page 161 Commissioning Manual Download

Page: 161 / 176

8.2.3

Additional indications

The additional indication messages do not activate internal fault or warning.

The messages are listed in the LHMI menu under the event list. The signal status data
is found under the IED status and in the internal event list.

Table 16:

Additional indications

Warning indication

Additional information

Time Synch Error

Source of the time synchronization is lost or time

system has made a time reset.

BATTERY1 Error

Auxiliary power is disconnected.

Settings Changed

Settings have been changed.

Setting Groups Changed

Setting group has been changed.

8.3

Correction procedures

8.3.1

Changing and setting the password

The password can only be set with PCM600.

For more information, see PCM600 documentation.

8.3.2

Identifying IED application problems

Navigate to the appropriate menu in the LHMI to identify possible problems.

•

Check that the function is on.

•

Check that the correct setting group (1 to 4) is activated.

•

Check the blocking.

•

Check the mode.

•

Check the measurement value.

•

Check the connection to trip and DFR functions.

•

Check the channel settings.

1MRK 506 331-UUS A

Section 8

Troubleshooting

153

Commissioning Manual

Summary of Contents for Relion 650 Series REL650
















































































































































































Search results

Summary of Contents for Relion 650 Series REL650

Reviews:

Related manuals for Relion 650 Series REL650

Brands by name

Popular brands

ABB Relion 650 Series REL650, Commissioning Manual

Search results

Summary of Contents for Relion 650 Series REL650

Reviews:

Related manuals for Relion 650 Series REL650

Brands by name

Popular brands